- Ei Compendex
- Scopus
- DOAJ
- Chinese Science Citation Database (CSCD)
- World Journals Clout Index Report
- T1 level in Directory for Mechanical EngineeringDisciplines
| Citation: |
ZHAO Xinyu, LIU Qiang, CHENG Guowen, LIN Tiesong, HUANG Yongde. Impact of copper-plated carbon nanotubes on microstructure and properties of copper-based composite films[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2023, 44(12): 56-62. DOI: 10.12073/j.hjxb.20230613014
|
Solving the problem of carbon nanotube aggregation and improving the interface between carbon nanotubes and matrix materials are the key to improving the properties of carbon nanotube copper-based composite films. In this study, the influence of copper-plated carbon nanotubes on the microstructure and properties of composite films has been conducted by comparing the differences in microstructure and properties between carbon nanotube copper-based composite films and copper-plated carbon nanotube copper-based composite films. This analysis involve the application of the quantum tunneling effect, DLVO theory and relevant material mechanics theories. The results indicate that at a content of 1.0% (mass fraction) of uncoated carbon nanotubes and copper-plated carbon nanotubes, the electrical resistivity of carbon nanotube copper-based composite films and copper-plated carbon nanotube copper-based composite films are 25.17 μΩ·cm and 17.73 μΩ·cm respectively. The rate of change in resistance under different bending cycles has been found to be greater for the former than for the latter. After copper plating on carbon nanotubes, the changes in their size and surface structure suppress agglomeration, enhance their joining strength with the copper matrix, and ultimately enhance the properties of composite films. Considering the influence of reinforcing materials on the microstructure and properties of composite materials, the mechanism of the influence of copper-plated carbon nanotubes on the microstructure and properties of copper -based composite films has been obtained. These findings provide a theoretical basis for subsequent research on flexible printing electronic technology.
| [1] |
Sundriyal P, Bhattacharya S. Inkjet-printed electrodes on A4 paper substrates for low-cost, disposable, and flexible asymmetric supercapacitors[J]. ACS Applied Materials & Interfaces, 2017, 9(44): 38507 − 38521.
|
| [2] |
黄永德, 彭鹏, 郭伟, 等. 纳米铜基柔性导电薄膜制备现状及前景[J]. 焊接学报, 2022, 43(11): 147 − 156.
Huang Yongde, Peng Peng, Guo Wei, et al. Current status and prospect of preparation of nano-copper based flexible conductive films[J]. Transactions of the China Welding Institution, 2022, 43(11): 147 − 156.
|
| [3] |
Wang Y, Xu C, Yu X, et al. Multilayer flexible electronics: Manufacturing approaches and applications[J]. Materials Today Physics, 2022, 23: 100647.
|
| [4] |
王帅奇, 邹贵生, 刘磊. 先进封装中铜-铜低温键合技术研究进展[J]. 焊接学报, 2022, 43(11): 112 − 125.
Wang Shuaiqi, Zou Guisheng, Liu Lei. Research progress of low-temperature Cu-Cu bonding technology for advanced packaging[J]. Transactions of the China Welding Institution, 2022, 43(11): 112 − 125.
|
| [5] |
邹贵生, 闫剑锋, 母凤文, 等. 微连接和纳连接的研究新进展[J]. 焊接学报, 2011, 32(4): 107 − 112.
Zou Guisheng, Yan Jianfeng, Mu Fengwen, et al. Recent progress in microjoining and nanojoining[J]. Transactions of the China Welding Institution, 2011, 32(4): 107 − 112.
|
| [6] |
李昭, 刘洋, 张浩, 等. 多尺度纳米银烧结接头连接强度及塑性[J]. 焊接学报, 2019, 40(10): 106 − 110.
Li Zhao, Liu Yang, Zhang Hao, et al. Bonding strength and plasticity of multiscale composite nanosilver paste for low temperature sintering[J]. Transactions of the China Welding Institution, 2019, 40(10): 106 − 110.
|
| [7] |
He C, Xu B, Li X. Effects of modified single-wall carbon nanotubes on the mechanical properties of polyvinyl alcohol composites by molecular dynamics simulation[J]. Materials Today Communications, 2023, 35: 105598. doi: 10.1016/j.mtcomm.2023.105598
|
| [8] |
亓钧雷, 万禹含, 张丽霞, 等. 碳纳米管增强TiNi复合钎料的制备与表征[J]. 焊接学报, 2014, 35(3): 27 − 30.
Qi Junlei, Wan Yuhan, Zhang Lixia, et al. Synthesis and characterization of carbon nanotubes reinforced TiNi composite solder[J]. Transactions of the China Welding Institution, 2014, 35(3): 27 − 30.
|
| [9] |
Ingo Alig, Pötschke P, Lellinger D, et al. Establishment, morphology and properties of carbon nanotube networks in polymer melts[J]. Polymer, 2012, 53(1): 4 − 28. doi: 10.1016/j.polymer.2011.10.063
|
| [10] |
Gu Y, Wu A, Federici J F, et al. Inkjet printable constantan ink for the fabrication of flexible and conductive film[J]. Chemical Engineering Journal, 2017, 313: 27 − 36. doi: 10.1016/j.cej.2016.12.071
|
| [11] |
冯敏. 碳纳米管化学镀铜增强铜基复合材料的工艺研究[D]. 昆明: 昆明理工大学, 2017.
Feng Min. Process research on electroless copper plating of carbon nanotubes reinforced copper matrix composites[D].Kunming: Kunming University of Science And Technology, 2017.
|
| [12] |
Zeng M, Ling Y, Zhang P, et al. Improvement of interfacial interaction and mechanical properties in aluminum matrix composites reinforced with Cu-coated carbon nanotubes[[J]. Materials Science & Engineering, A, 2023, 870: 144918.
|
| [13] |
Maqbool A, Hussain M A, Khalid F A, et al. Mechanical characterization of copper coated carbon nanotubes reinforced aluminum matrix composites[J]. Materials Characterization, 2013, 86(8): 39 − 48.
|
| [14] |
Joo S J, Park S H, Moon C J, et al. A highly reliable copper nanowire/ nanoparticle ink pattern with high conductivity on flexible substrate prepared via a flash light-sintering technique[J]. ACS Applied Materials & Interfaces, 2015, 7(10): 5674 − 5684.
|
| [15] |
潘静, 卞立春, 高明. 团聚参数对纳米复合材料性能的影响分析[C]//中国力学大会-2017暨庆祝中国力学学会成立60周年大会论文集(A) , 2017.
Pan Jing, Bian Lichun, Gao Ming. The effect of agglomeration parameters on the properties of nanocomposites[C]//Chinese Congress of Theoretical and Applied Mechanics-Proceedings of the 2017 Celebration of the 60th Anniversary of the Establishment of the Chinese Congress of Theoretical and Applied Mechanics (A) , 2017.
|
| [16] |
刘中常. 纳米材料中纳米粒子团聚的原因及解决方法[J]. 价值工程, 2017, 36(13): 2.
Liu Zhongchang. Reason for aggregation of nanoparticles in nano-materials and solutions[J]. Value Engineering, 2017, 36(13): 2.
|
| [17] |
Khan I A, Flora J R V, Afrooz A R M N, et al. Change in chirality of semiconducting single-walled carbon nanotubes can overcome anionic surfactant stabilisation: a systematic study of aggregation kinetics[J]. Environmental Chemistry, 2015, 12(6): 652. doi: 10.1071/EN14176
|
| [18] |
郭鲤, 詹浩, 游玉萍, 等. 预处理及化学镀铜后碳纳米管的微观形貌及成分[J]. 机械工程材料, 2019, 43(8): 6.
Guo Li, Zhan Hao, You Yuping, et al. Micromorphology and chemical composition of carbon nanotubes after pretreatment and electroless copper plating[J]. Materials for Mechanical Engineering, 2019, 43(8): 6.
|
| [19] |
王艳. 碳纳米管铜复合材料的制备及性能研究[D]. 郑州: 郑州航空工业管理学院, 2019.
Wang Yan. Study on preparation and properties of carbon nanotube/copper composites[D]. Zhengzhou: Zhengzhou University of Aeronautics, 2019.
|
| [20] |
Chen B, Li S, Imai H, et al. Load transfer strengthening in carbon nanotubes reinforced metal matrix composites via in-situ tensile tests[J]. Composites Science & Technology, 2015, 113(5): 1 − 8.
|
| [1] | ZHONG Pu, LI Liangyu, REN Guochun, WANG Tianqi, GUO Dongbo. "Γ" shaped arc and its promotion method in Tri-Arc dual wire welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2024, 45(2): 54-60. DOI: 10.12073/j.hjxb.20230827001 |
| [2] | WANG Ziran, MIAO Yugang, WANG Lin, MA Xubo, WEI Chao, ZHANG Benshun. Numerical analysis and mechanism investigation of the bypass-current plasma-MIG hybrid arc and the molten pool[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2023, 44(8): 1-6, 13. DOI: 10.12073/j.hjxb.20220909004 |
| [3] | WANG Bo, SANG Jian, ZHANG Hongtao, TENG Yao, WANG Qichen. Analysis on welding processing properties of plasma-TIG coupling arc hybrid welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(6): 94-99. DOI: 10.12073/j.hjxb.2019400161 |
| [4] | HUANG Yong, HAO Yanzhao, LIU Ruilin. Investigation on coupling arc electrode GPCA-TIG welding process[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2014, 35(3): 19-22. |
| [5] | HUANG Yong, HAO Yanzhao, QU Huaiyu, LIU Ruilin. Test and analysis of arc pressure measurement in coupling arc electrode TIG welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2013, (12): 33-36. |
| [6] | HUANG Yong, QU Huaiyu, FAN Ding, LIU Ruilin, KANG Zaixiang, WANG Xinxin. Arc pressure measurement and analysis of coupling arc AATIG[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2013, (3): 33-36. |
| [7] | XIA Yuan, SONG Yonglun, RAN Guowei, SHI Linan. Analysis on mechanism of laser-assisted TIG arc ignition[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2010, (1): 9-11,16. |
| [8] | LENG Xue-son, ZHANG Guang-jun, WU Lin. Analysis of twin-electrode TIG coupled arc pressure[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2006, (9): 13-16. |
| [9] | LU Feng-gui, TANG Xin-hua, LI Shao-qing, YAO Shun, LOU Song-nian. Stationary numerical simulation on coupling interaction between TIG welding arc and pool[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2005, (9): 69-72,76. |
| [10] | Li Liangyu, Zhang Guangjun, Li Liqun, Gao Hongming, Zhu Yujie. Mechanism of Starting Arc in Welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 1997, (4): 238-243. |
Supported by:
Beijing Renhe Information Technology Co. Ltd
DownLoad: