Forming mechanism of C<sub>f</sub>/SiC-Nb brazed joints reinforced by core-sheath structure

LI Guokun; YANG Mengying; PAN Yuanqiao; FENG Xinxin; WANG Yiru; WANG Zeyu

doi:10.12073/j.hjxb.20240906001

TRANSACTIONS OF THE CHINA WELDING INSTITUTION > 2025 > 46(2): 80-86. > DOI: 10.12073/j.hjxb.20240906001

LI Guokun, YANG Mengying, PAN Yuanqiao, FENG Xinxin, WANG Yiru, WANG Zeyu. Forming mechanism of C_f/SiC-Nb brazed joints reinforced by core-sheath structure[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2025, 46(2): 80-86. DOI: 10.12073/j.hjxb.20240906001

Citation:

PDF (7773 KB)

Forming mechanism of C_f/SiC-Nb brazed joints reinforced by core-sheath structure

School of Materials Science and Engineering, Jiangsu University, Zhenjiang, 212013, China

More Information

Received Date: September 05, 2024
Available Online: February 23, 2025

Graphical Abstract

Abstract

Abstract

In order to address the issues of high residual stress and low strength in the brazed joints between ceramic-matrix composites and metals, a hollow-skeleton network-structured carbon sponge was used as an interlayer to relieve the joint stress and improve the mechanical properties of the joint. The melamine-formaldehyde foam was subjected to rapid high-temperature carbonization treatment in a vacuum environment to obtain a hollow carbon sponge with continuous skeletons and uniform pores. Subsequently, it was used as an interlayer to assist in the brazing process between C_f /SiC composites and Nb. The results show that under the brazing parameter of 850 ℃/10 min, the Ag-27Cu-3.5Ti filler metal fully filled the hollow space of the carbon sponge and reacted with the carbon sponge skeleton to form a core-sheath structure in which the filler metal alloy was coated with TiC. When using the thickness of the carbon sponge interlayer as 2.0 mm, the joint strength reached a maximum value of 112.6 MPa, which is 56% higher than that of the direct brazed joint without an interlayer. This is attributed to the multiple synergistic strengthening effects of the core-sheath structure on the joint.
- brazing,
- residual stress,
- carbon sponge,
- mechanical properties,
- core-sheath structure

FullText(HTML)

References (19)

References

[1]	刘玉章, 张丽霞, 杨振文, 等. C/SiC复合材料表面状态对其与Nb钎焊的影响[J]. 焊接学报, 2010, 31(10): 31 − 34. Liu Yuzhang, Zhang Lixia, Yang Zhenwen, et al. Effects of surface state of C/SiC composites on brazing of C/SiC to Nb[J]. Transactions of the China Welding Institution, 2010, 31(10): 31 − 34.
[2]	王泽宇. 碳基网络复合中间层辅助钎焊C/C复合材料与Nb机理研究[D]. 哈尔滨: 哈尔滨工业大学, 2020. Wang Zeyu. Study on the brazing mechanism of carbon fiber reinforce carbon composite-Niobium by using carbonaceous network interlayer [D]. Harbin: Harbin Institute of Technology, 2020.
[3]	Wang Z Y, Li G K, Yang M Y, et al. An in situ 3D core-sheath interlayer utilized for reinforcing a WC-Co/3Cr13 brazed joint[J]. Journal of the American Ceramic Society, 2024, 107(9): 5981 − 5992. doi: 10.1111/jace.19900
[4]	张冠星, 钟素娟, 沈元勋, 等. 梯度三明治钎料钎焊过程组织演变及力学性能分析[J]. 焊接学报, 2023, 44(9): 37 − 43. doi: 10.12073/j.hjxb.20221020001 Zhang Guanxing, Zhong Sujuan, Shen Yuanxun, et al. Research on microstructure evolution and mechanical properties of gradient sandwich filler metal during brazing[J]. Transactions of the China Welding Institution, 2023, 44(9): 37 − 43. doi: 10.12073/j.hjxb.20221020001
[5]	Zhang Y, Guo X M, Guo W, et al. Effect of Cu foam on the microstructure and strength of the SiC_f/SiC-GH536 brazed joint[J]. Ceramics International, 2022, 48(9): 12945 − 12953. doi: 10.1016/j.ceramint.2022.01.167
[6]	Ma Q, Li Z R, Ba J, et al. Relieving residual stress in brazed joint between SiC and Nb using a 3D-SiO₂-fiber ceramic interlayer[J]. Vacuum, 2018, 149: 93 − 95. doi: 10.1016/j.vacuum.2017.12.022
[7]	林盼盼, 杨佳, 步澜斌, 等. TiZrNiCu钎焊(C_f-SiC_f)/SiBCN与Nb的界面产物及机理分析[J]. 焊接学报, 2019, 40(9): 7 − 13. Lin Panpan, Yang Jia, Bu Lanbin, et al. Microstructure evolution and joining mechanism of brazing (C_f-SiC_f)/SiBCN to Nb with TiZrNiCu[J]. Transactions of the China Welding Institution, 2019, 40(9): 7 − 13.
[8]	郝通达. VFG/CuTi钎焊SiO2复合材料与Invar合金工艺及机理研究[D]. 哈尔滨: 哈尔滨工业大学, 2016. Hao Tongda. Research on processing and mechanism of brazing SiO₂ composites and Invar alloy with VFG/CuTi [D]. Harbin: Harbin Institute of Technology, 2016.
[9]	Dou Y Y, Wang Z P, He W Q, et al. Artificial spider silk from ion-doped and twisted core-sheath hydrogel fibres[J]. Nature Communications, 2019, 10(1): 52 − 93. doi: 10.1038/s41467-018-07965-6
[10]	Xu Z X, Deng W J, Wang X L. 3D Hierarchical carbon-rich micro-/nanomaterials for energy storage and catalysis[J]. Electrochemical Energy Reviews, 2021, 4(2): 269 − 335.
[11]	Kang S F, Chen M Y, Wang Y T, et al. Engineering a 3D porous carbon sponge as a self-floating solar energy utilization platform for photothermal oil spill recovery and photocatalytic H2 evolution[J]. Sustainable Energy and Fuels, 2022, 7: 409 − 419.
[12]	Zhang L P, Liu W, Chen S, et al. Engineering stable carbon sponge with moderate interlayer spacing and porous architecture for rapid K⁺-intercalation[J]. Electrochimica Acta, 2023, 451: 142214. doi: 10.1016/j.electacta.2023.142214
[13]	Li W, Xu F J, Liu W, et al. Flexible strain sensor based on aerogel-spun carbon nanotube yarn with a core-sheath structure[J]. Composites Part A, 2018, 108: 107 − 113. doi: 10.1016/j.compositesa.2018.02.024
[14]	Lu Y M, Zhao X N, Lin Y, et al. Lightweight MXene/carbon composite foam with hollow skeleton for air-stable, high-temperature-resistant and compressible electromagnetic interference shielding[J]. Carbon, 2023, 206(25): 375 − 382.
[15]	Zhong H Z, Song T T, Li C W, et al. The Gibson-Ashby model for additively manufactured metal lattice materials: Its theoretical basis, limitations and new insights from remedies[J]. Current Opinion in Solid State & Materials Science, 2023, 27(3): 101081.
[16]	Wang P C, Liu W H, Li J Z, et al. Unrevealing the wetting behavior and mechanism of AgCuTi filler on negative thermal expansion Sc₂W₃O₁₂ materials: Experiments and First-principles calculations[J]. Applied Surface Science, 2024, 652: 159 − 257.
[17]	Zhang L X, Yang J H, Sun Z, et al. Vacuum brazing Nb and BN-SiO₂ ceramic using a composite interlayer with network reinforcement architecture[J]. Ceramics International, 2017, 43(11): 8126 − 8132. doi: 10.1016/j.ceramint.2017.03.136
[18]	Song X G, Zhao Y X, et al. Wetting of AgCu-Ti filler on porous Si3N4 ceramic and brazing of the ceramic to TiAl alloy[J]. Ceramics International, 2018, 44(5): 4622 − 4629. doi: 10.1016/j.ceramint.2017.11.212
[19]	Bauer J, Martí S C, Mahsa A, et al. Nanoarchitected metal/ceramic interpenetrating phase composites[J]. Science Advances, 2022, 8(33): eabo3080. doi: 10.1126/sciadv.abo3080

[1]	LIU Yazhou, SONG Xiaoguo, CHENG Weiwei, HU Shengpeng, CAO Jian. Mechanical properties of brazed ultra-thin GH99 honeycomb sandwich structure[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2022, 43(11): 1-7. DOI: 10.12073/j.hjxb.20220706001
[2]	GUO Shun, WANG Pengxiang, ZHOU Qi, ZHU Jun, GU Jieren. Microstructure and mechanical properties of bimetallic intertexture structure fabricated by plasma arc additive manufacturing[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2021, 42(3): 14-19. DOI: 10.12073/j.hjxb.20201125004
[3]	DENG Yunhua, YUE Xishan, TAO Jun, JING Xiaodong. Study on the brazing process of titanium sound-reduction honeycomb core sandwich structure[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(11): 139-146. DOI: 10.12073/j.hjxb.2019400301
[4]	WANG Xiaoguang1, LI Xiaoyang2, CHEN Shujun2, YU Huiping2, LI Xiang2. Mechanic parameters analysis of spot welded low carbon steel structure[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2018, 39(3): 107-111. DOI: 10.12073/j.hjxb.2018390079
[5]	JIANG Xiaoxia, ZHU Liang, QIAO Jisen, WU Yixiong, LI Zhuguo, CHEN Jianhong. Stiffness analysis considering joint geometry parameters of I-core steel sandwich plates[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2015, 36(11): 45-48.
[6]	ZHANG Min, LIU Mingzhi, CHEN Yangyang, LI Jihong. Development of self-shielded flux cored wire for X100 pipeline steel and performance analysis of welded joints[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2014, 35(10): 1-4.
[7]	DONG Honggang, YANG Liqun, ZHAI Nan, DONG Chuang. Analysis on microstructure and mechanical properties of aluminum alloy/stainless steel joint made with flux-cored filler metal[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2011, (10): 1-4.
[8]	WANG Hui, HE Deping, CHU Xuming, HE Siyuan. Interface structure of N₂-shielded furnace brazing of Al foam and its mechanical properties[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2008, (10): 1-4, 8.
[9]	YU Ping, PAN Chuan, XUE Jin. Effect of Fe₂O₃ on self-shielded flux cored wire[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2004, (2): 91-94,98.
[10]	SHAN Ping, YI Xiao lin, HU Sheng sun, LUO Zhen. Detection of plasma sheath voltage in plasma arc welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2003, (2): 19-21,26.

Cited By

Cited by

Periodical cited type(2)

1.	康蕾，刘飞，陈韬. 1050A纯铝/TA15钛合金异种金属冷焊接头组织与性能. 焊接. 2024(12): 61-66 .
2.	闫耀天，刘柏深，曹健，亓钧雷. 直流电热冲击辅助多组分氧化物钎焊SiC陶瓷的工艺及性能. 焊接学报. 2022(11): 22-29+164 . 本站查看

Other cited types(0)

Get Citation

PDF

XML

Article views (32) PDF downloads (20) Cited by(2)

Turn off MathJax

Article Contents

Abstract

References

Forming mechanism of C_f/SiC-Nb brazed joints reinforced by core-sheath structure