Citation: | ZHANG Kai, GAO Hui, LIN Yuanhao, SHAO Mingqi. Process parameters analysis of coaxial powder feeding argon arc cladding based on RSM and NSGA-II algorithm[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2024, 45(12): 106-116. DOI: 10.12073/j.hjxb.20231107005 |
In order to improve the quality and performance of the cladding layer on the surface of the re-repaired workpiece, the argon arc cladding experiment of Nano-SiC reinforced wear-resistant coating was carried out on the surface of 316 L stainless steel by using the self-developed coaxial powder feeding tungsten argon arc cladding system. Aiming at the problem that the process parameters are difficult to optimize under the interaction of multiple factors, a multi-objective optimization method of process parameters integrated with RSM and NSGA-II algorithm is proposed. In this method, the welding unit heat input, powder feeding amount and SiC quality fraction were taken as input factors, and the microhardness, penetration depth and dilution rate were taken as response indexes. The regression model between the quality of cladding layer and process parameters was established by response surface method, and the interaction effect of process parameters on the quality of cladding layer was explored. Then, the NSGA-II algorithm was used to find the optimal combination of process parameters. Finally, the quality comparison and microstructure observation of cladding layer were carried out on the samples prepared under the optimal process parameters. The results show that the optimal parameter combination is unit heat input is 17.82 W/(mm·min−1), powder feeding amount 8g/mm and SiC quality fraction 2%. The microhardness of the specimens under these conditions increased by 9.9%, the depth of fusion decreased by 31.9%, the dilution rate decreased by 22.4%. The morphology of the cladding layer is good without defects, and the top area is uniform and fine equiaxed grains.
[1] |
朱明冬, 吴冰洁, 曹立彦, 等. 304LN不锈钢表面激光熔覆钴基合金组织和性能[J]. 焊接学报, 2022, 43(8): 48 − 53. doi: 10.12073/j.hjxb.20220508001
Zhu Mingdong, Wu Bingjie, Cao Liyan, et al. The microstructure and properties of laser cladding cobalt-based alloy on the surface of 304LN stainless steel[J]. Transactions of the China Welding Institution, 2022, 43(8): 48 − 53. doi: 10.12073/j.hjxb.20220508001
|
[2] |
郗文超, 宋博学, 王钊, 等. 表面熔覆工艺的成形特征及粉末有效利用率研究[J]. 表面技术, 2019, 48(3): 211 − 218.
Xi Wenchao, Song Boxue, Wang Zhao, et al. Study on the forming characteristics and effective utilization rate of powder of surface cladding process[J]. Surface Technology, 2019, 48(3): 211 − 218.
|
[3] |
Raghavendra C R, Satyappa Basavarajappa, Irappa Sogalad, et al. Study on Ni composite coating on Al6061 substrate material with different nano particle reinforcement by electrodeposition process[J]. Materials Today: Proceedings, 2020, 24(Part2): 1680 − 1685.
|
[4] |
王子龙, 秦建, 路全彬, 等. 焊接方法对 S22053 双相钢焊接接头组织和性能的影响[J]. 焊接, 2018(8): 21 − 27.
Wang Zilong, Qin Jian, Lu Quanbin, et al. Effects of welding methods on microstructure and properties of welded joints of S22053 dual phase steel[J]. Welding & Joining, 2018(8): 21 − 27.
|
[5] |
王金凤, 井子润, 杨伟, 等. 激光熔覆与等离子熔覆的镍基合金熔覆层组织和性能对比[J]. 材料保护, 2020, 53(1): 80 − 83.
Wang Jinfeng, Jing Zirun, Yang Wei, et al. Comparison of microstructure and properties of Ni-based alloy cladding layer by laser cladding and plasma cladding[J]. Materials Protection, 2020, 53(1): 80 − 83.
|
[6] |
Rajeev R, Kumar A D. Recent advancements in surface modification by gas tungsten arc cladding technique: a review[J]. Advanced Materials Research, 2022, 6608: 113 − 122.
|
[7] |
王浡婳, 张立杰. AZ91D镁合金表面氩弧熔覆Nd/TiC耐磨涂层的特性研究[J]. 粉末冶金工业, 2021, 31(3): 63 − 67.
Wang Bohua, Zhang Lijie. Study on the characteristics of Nd / TiC wear-resistant coating on AZ91D magnesium alloy by argon arc cladding[J]. Powder Metallurgy Industry, 2021, 31(3): 63 − 67.
|
[8] |
Kumar P, Sinha N A, Hirwani K C, et al. Investigation of TIG cladding of NiTi wire on substrate 304L to study the effect of applied current on microstructure and mechanical properties[J]. Transactions of the Indian Institute of Metals, 2021, 74(6): 1333 − 1348. doi: 10.1007/s12666-021-02213-w
|
[9] |
王婉婉, 高辉, 周灿丰, 等. 同轴送粉TIG熔覆过程数值模拟与试验研究[J]. 兵器材料科学与工程, 2023, 46(5): 70 − 75.
Wang Wanwan, Gao Hui, Zhou Canfeng, et al. Numerical simulation and experimental study on coaxial powder feeding TIG cladding process[J]. Ordnance Material Science and Engineering, 2023, 46(5): 70 − 75.
|
[10] |
Fesharaki N M , Shoja Razavi R , Mansouri A H, et al. Microstructure investigation of Inconel 625 coating obtained by laser cladding and TIG cladding methods[J]. Surface & Coatings Technolog, 2018: 35325 − 35331.
|
[11] |
胡言峰, 杜彦斌, 许磊, 等. 响应面法与粒子群算法集成的激光熔覆工艺参数优化方法[J]. 机械科学与技术, 2023, 42(4): 629 − 637.
Hu Yanfeng, Du Yanbin, Xu Lei, et al. Optimization method of laser cladding process parameters based on response surface method and particle swarm optimization algorithm[J]. Mechanical Science and Technology for Aerospace Engineering, 2023, 42(4): 629 − 637.
|
[12] |
马小英, 孙志礼, 张毅博, 等. 基于Kriging-PSO智能算法优化焊接工艺参数[J]. 东北大学学报(自然科学版), 2019, 40(3): 370 − 374. doi: 10.12068/j.issn.1005-3026.2019.03.013
Ma Xiaoying, Sun Zhili, Zhang Yibo, et al. Optimization of welding process parameters based on Kriging-PSO intelligent algorithm[J]. Journal of Northeastern University (Natural Science), 2019, 40(3): 370 − 374. doi: 10.12068/j.issn.1005-3026.2019.03.013
|
[13] |
Deb K, Pratap A, Agarwal S, et al. A fast and elitist multiobjective genetic algorithm: NSGA-Ⅱ[J]. IEEE Transactions on Evolutionary Computation, 2002, 6(2): 182 − 197. doi: 10.1109/4235.996017
|
[14] |
Acherjee B, Kuar A S, Mitra S, et al. Effect of carbon black on temperature field and weld profile during laser transmission welding of polymers: a FEM study[J]. Optics & Laser Technology, 2012, 44(3): 514 − 521. doi: 10.1016/j.optlastec.2011.08.008
|
[15] |
王群, 余洋, 钱志强. 基于响应面法的HR-2抗氢钢电子束插接焊工艺参数优化[J]. 焊接学报, 2023, 44(4): 50 − 57. doi: 10.12073/j.hjxb.20220522001
Wang Qun, Yu Yang, Qian Zhiqiang. Optimization of electron beam welding process parameters of HR-2 hydrogen resistant steel based on response surface method[J]. Transactions of the China Welding Institution, 2023, 44(4): 50 − 57. doi: 10.12073/j.hjxb.20220522001
|
[16] |
Mohammed J K Bashir, Hamidi Abdul Aziz, Yusoff Mohd Suffian, et al. Application of response surface methodology (RSM) for optimization of ammoniacal nitrogen removal from semi-aerobic landfill leachate using ion exchange resin[J]. Desalination, 2010, 254(1-3): 154 − 161. doi: 10.1016/j.desal.2009.12.002
|
[17] |
Dikshit Mithilesh K, Suryansh Singh, Pathak V, et al. Surface characteristics optimization of biocompatible Ti6Al4V with RCCD and NSGA II using die sinking EDM[J]. Journal of Materials Research and Technology, 2023, 24: 223 − 235. doi: 10.1016/j.jmrt.2023.03.005
|
[18] |
Ma S M, Zhang A H, Gu J J. Multi-objective optimization of process parameters for ultra-narrow gap welding based on Universal Kriging and NSGA Ⅱ[J]. China Welding, 2023, 32(3): 28 − 35.
|
[1] | ZHANG Qunbing, NIU Jing, ZHAO Pengfei, HUANG Yong, LI Zhigang, ZHANG Jianxun. Influence of preheating temperature on cold cracking sensitivity of 12Cr10Co3W2Mo heat resistant steel[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2015, 36(4): 87-91. |
[2] | LI Yajuan, JIA Peng, LI Wushen, XIE Qi. Establishment of cold cracking susceptibility criterion for X80 pipeline steel[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2012, (4): 85-88. |
[3] | YANG Jianguo, HUANG Luyong, ZHANG Yong, FANG Hongyuan. Mechanism of cold welding cracks in 30CrMnSi steel joints welded by TIG method[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2011, (12): 13-16. |
[4] | TENG Bin, LI Xiaoyu, LEI Zhen, WANG Xuyou. Analysis on cold crack sensitivity of low alloy high strength steel weld by laser-arc hybrid welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2010, (11): 61-64. |
[5] | HUANG Fuxiang, DU Zeyu, SUI Yongli, ZENG Huilin, GUO Xiaojiang. Study on cold cracking susceptibility of domestic X80 pipeline steel using implant tests[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2009, (4): 89-92. |
[6] | ZHANG Guang-xian, ZHOU Zeng-da, CHEN Ren-fu, YIN Hai, LIU Ming-zhi. Research on simulation for surface tension transformation in CO2 arc welding[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2003, (4): 68-72. |
[7] | REN Zhen-an, ZHOU Zhen-feng, SUN Da-qian. Advance of Researches on the Cold Cracking of the Gray Cast Iron Cold-welding with Homogenous Welding Consumables[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2001, (1): 91-96. |
[8] | HUANG Peng-fei, LU Zhen-yang, CHEN Shu-jun, YIN Shu-yan. Functions of Output Filter Inductor in CO2 Gas Shielded Arc Welding Inverteer[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2000, (2): 81-84. |
[9] | Ren Zhenan, Sun Daqian, Zhou Zhenfeng. Microscopic Redistribution Behaviours and Bubbling-up Characteristic of Residual Diffusible Hydrogen in the Grey Iron Weldment[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 1998, (4): 36-41. |
[10] | Zhang Bingfan, Ma Yuanlin, Zeng Yuejian, Li Wushen. Effects of weld metals on cold crack resistance in HAZ for high strength steels[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 1991, (1): 31-38. |