Design modeling and experimental verifications of the laminated busbar for high frequency arc welding inverter

HE Yaning; XIONG Gang

doi:10.12073/j.hjxb.2019400244

TRANSACTIONS OF THE CHINA WELDING INSTITUTION > 2019 > 40(9): 104-110. > DOI: 10.12073/j.hjxb.2019400244

HE Yaning, XIONG Gang. Design modeling and experimental verifications of the laminated busbar for high frequency arc welding inverter[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(9): 104-110. DOI: 10.12073/j.hjxb.2019400244

Citation:

PDF (1356 KB)

Design modeling and experimental verifications of the laminated busbar for high frequency arc welding inverter

Chengdu Xionggu Jiashi Electrical Co., Ltd., Chengdu 611731, China

More Information

Received Date: March 30, 2018

Graphical Abstract

Abstract

Abstract

With the increase of switching frequency, reducing stray inductance becomes one of the key factors in designing high frequency arc welding inverter. In order to meet the demand of DPS-500 of 50 kHz/20 kW, a laminated busbar was designed, which integrated DC link capacitor, soft start circuit, IGBT module and three-phase rectifier module. The numerical calculation of quasi-static electromagnetic field was carried out using ANSYS Q3D. Parasitic parameter matrices were extracted. The multi-port circuit model of the laminated busbar was built. The impedance vs frequency characteristic and the switching behavior of the laminated busbar was simulated and measured individually based on impedance resonance method and double pulse test method. Stray inductance of the laminated busbar was extracted by two different ways aforementioned. The results showed that the design was valid. The modeling accuracy of the laminated busbar was verified in frequency and temporal-domain by comparing results of simulation and experiment. Finally, the causes of errors was discussed.
- stray inductance,
- laminated busbar,
- impedance resonance method,
- double pulse test,
- multi-port circuit model

FullText(HTML)

References (20)

References

张晓囡,李俊岳,黄石生,等.评定CO₂电弧焊电源动特性的统计分析法[J].焊接学报, 2001, 22(3):12-16 Zhang Xiaonan, LI Junyue, Huang Shisheng, et al. Statistical analyzing evaluation method of dynamic characteristic of CO₂ arc welding power source[J]. Transactions of the China Welding Institution, 2001, 22(3):12-16

潘际銮.现代弧焊控制[M].北京:机械工业出版社, 2000.

何亚宁.峰值电流模式PSFB-ZVS逆变焊接电源的完整小信号模型及控制环路设计[J].焊接学报, 2016, 37(1):81-84 He Yaning. Small-signal modeling for peak current mode PSFB-ZVS PWM arc-welding inverter and control loop design[J]. Transactions of the China Welding Institution, 2016, 37(1):81-84

王振民,汪倩,王鹏飞,等.新一代WBG弧焊逆变电源[J].焊接学报, 2016, 37(7):49-52 Wang Zhenmin, Wang Qian, Wang Pengfei, et al. A new generation WBG arc welding inverter[J]. Transactions of the China Welding Institution, 2016, 37(7):49-52

福尔克,郝康普,韩金刚. IGBT模块:技术、驱动和应用[M].北京:机械工业出版社, 2016.

Caponet M C, Profumo F, De Doncker R W, et al. Low stray inductance bus bar design and construction for good EMC performance in power electronic circuits[J]. IEEE Transactions on Power Electronics, 2002, 17(2):225-231.

Popova L, Musikka T, Juntunen R, et al. Design and modeling of low-inductive busbars for a three-level ANPC inverter[J]. International Review of Electrical Engineering, 2014, 9(1):7-15.

Lounis Z, Rasoanarivo I, Davat B. Minimization of wiring inductance in high power IGBT inverter[J]. IEEE Transactions on Power Delivery, 2000, 15(2):551-555.

汪鋆,杨兵建,徐枝新,等. 750 kVA高功率密度二极管钳位型三电平通用变流模块的低感叠层母线排设计[J].中国电机工程学报, 2010, 30(18):47-54 Wang Jun, Yang Bingjian, Xu Zhixin, et al. Configuration of low inductive laminated busbar in 750 kVA NPC three-level universal converter module of high power density[J]. Proceeding of the CSEE, 2010, 30(18):47-54

Chen C, Pei X, Shi Y, et al. Modeling and optimization of high power inverter three-layer laminated busbar[C]//Energy Conversion Congress and Exposition. IEEE, 2012:1380-1385.

何亚宁.一开机浪涌电流抑制电路:中国, 201410036003.0[P]. 2016-01-20.

薛高飞,潘启军,吴文力,等.三相三电平逆变装置全系统电路仿真模型研究[J].电机与控制学报, 2014, 18(4):17-24 Xue Gaofei, Pan Qijun, Wu Wenli, et al. Research on systematic simulation model of 3-phase 3-level inverter[J]. Electric Machines and Control, 2014, 18(4):17-24

Yang L, Odendaal W G H. Measurement-based method to characterize parasitic parameters of the integrated power electronics modules[J]. IEEE Transactions on Power Electronics, 2007, 22(1):54-62.

吴文力,赵治华,潘启军,等. IGBT复合母排换流回路电感研究[J].电力电子技术, 2013, 47(2):36-37 Wu Wenli, Zhao Zhihua, Pan Qijun, et al. Study of current transition loop inductance for the IGBT bus-bar[J]. Power Electronics, 2013, 47(2):36-37

朱楠,陈敏,徐德鸿.低寄生电感IGBT功率模块的设计及测试[C]//中国电源学会学术年会.杭州:2013, 76-82.

冯高辉,袁立强,赵争鸣,等.基于开关瞬态过程分析的母排杂散电感提取方法研究[J].中国电机工程学报, 2014, 34(36):6442-6449 Feng Gaohui, Yuan Liqiang, Zhao Zhengming, et al. A novel stray inductance extraction method for bus bars based on turn-on/off transient process[J]. Proceedings of the CSEE, 2014, 34(36):6442-6449

Daou H, Ameziani M, Lhotellier D, et al. Dynamic electric model for IGBT power module based on Q3D^® and Simplorer^®:3D Layout design, stray inductance estimation, experimental verifications[C]//International Conference on Electrical Systems for Aircraft. IEEE, 2017, 1-6.

何亚宁.一种用于功率半导体模块动态特性建模的封装寄生参数高效提取方法[J].电焊机, 2019, 49(6):100-106 He Yaning. A high efficiency parasitic parameters extraction method for dynamic characteristic modeling of power semiconductor modules[J]. Electric Welding Machine, 2019, 49(6):100-106

唐新灵,崔翔,赵志斌,等.压接式IGBT器件内部并联支路瞬态电流均衡特性的研究[J].中国电机工程学报, 2017, 37(1):233-243 Tang Xinling, Cui Xiang, Zhao Zhibin, et al. Analysis of transient current distribution characteristics of parallel chips in press pack IGBT[J]. Proceedings of the CSEE, 2017, 37(1):233-243

Xing K, Lee F C, Boroyevich D. Extraction of parasitics within wire-bond IGBT modules[C]//Applied Power Electronics Conference Exposition. IEEE, 1998, 497-503.

Cited By

Cited by

Periodical cited type(5)

1.	周立成，冯志军，谢广明，吴华锋，李泽华，胡大川. 水下搅拌摩擦焊对铝/铜接头组织与性能的影响. 精密成形工程. 2023(03): 97-104 .
2.	张茗瑄，马志鹏，陈桂娟，夏法锋，于心泷. 电磁超声作用下Sn-9Zn钎料在SiC表面铺展分析. 焊接学报. 2022(02): 55-60+117 . 本站查看
3.	邓呈敏，程东海，张华，王非凡，刘德博. 焊丝成分对铝/铜激光熔钎焊接头组织和性能的影响. 焊接学报. 2022(01): 16-21+114 . 本站查看
4.	陈克选，杜茵茵，陈彦强. 交变磁控电源的设计与仿真. 电焊机. 2022(03): 93-98 .
5.	于江，潘俊林，苗惺林，张洪涛，高建国，苏昭方. 铝/铜异种金属电阻热辅助超声波缝焊工艺特性. 焊接学报. 2022(07): 76-81+117-118 . 本站查看

Other cited types(3)

Get Citation

PDF

XML

Article views (522) PDF downloads (191) Cited by(8)

Turn off MathJax

Article Contents

Abstract

References

Design modeling and experimental verifications of the laminated busbar for high frequency arc welding inverter

Abstract

References

Cited by

Periodical cited type(5)

Other cited types(3)

Catalog

Export File

Citation

Format

Content