\n
\n
\n
\n
\n
\n
\n
\n
\n
\n Cr-Nb与V增强铁基堆焊涂层组织及高温摩擦学性能
Microstructure and high-temperature tribological properties of Cr-Nb and V-enhanced Fe-based hardfacing coatings deposited by submerged arc welding
\n
\n
\n
\n
\n -
\n
\n
-
\n \n \n\n\n 摘要: \n 为了明确不同合金化方式对铁基堆焊涂层高温摩擦磨损性能的影响,采用埋弧堆焊在Q235钢表面制备Cr-Nb和V涂层,分析其显微组织、室温硬度、高温硬度及600 ℃摩擦磨损性能,并通过XPS表征磨损表面化学状态.结果表明,2种涂层均含M7C3,并分别形成NbC和VC,碳化物体积分数分别为62.9% ± 4.2%和53.8% ± 1.8%;Cr-Nb涂层第2层室温基体区平均硬度为807.1 HV0.5,较V涂层高12.0%,V涂层在200 ~ 700 ℃下的硬度较高;600 ℃下,V涂层平均摩擦系数为0.43,比磨损率为1.06 × 10−4 mm3/(N·m),较Cr-Nb涂层和Q235基体分别降低43.6%和69.7%;其磨损表面存在与V2O5化学态相符的含钒氧化物,结合磨损形貌,推测碳化物承载与含钒氧化物的界面减摩作用共同促进了耐磨性的改善.较高的碳化物含量和室温硬度并未对应更低的高温磨损率,涂层的高温耐磨性还受到摩擦表面氧化行为的影响. \n\n \n
\n \n\n \n\n\n Abstract: \n To clarify the effects of different alloying strategies on the high-temperature friction and wear properties of Fe-based hardfacing coatings, Cr-Nb and V coatings were deposited on the surface of Q235 steel by submerged arc welding. Their microstructures, room-temperature hardness, high-temperature hardness, and friction and wear properties at 600 ℃ were analyzed, and the chemical states of the worn surfaces were characterized by XPS. The results indicate that both coatings contain M7C3, with NbC and VC formed in the Cr-Nb and V coatings, respectively. The carbide volume fractions are 62.9% ± 4.2% for the Cr-Nb coating and 53.8% ± 1.8% for the V coating. The average room-temperature hardness of the matrix region in the second layer of the Cr-Nb coating is 807.1 HV0.5, which is 12.0% higher than that of the V coating; however, the V coating exhibits higher hardness at 200–700 ℃. At 600 ℃, the V coating has an average friction coefficient of 0.43 and a specific wear rate of 1.06 × 10−4 mm3/(N·m). This specific wear rate is 43.6% lower than that of the Cr-Nb coating and 69.7% lower than that of the Q235 substrate. The worn surface of the V coating contains vanadium-containing oxides with chemical states consistent with V2O5. Together with the wear morphology, this finding suggests that load support by carbides and interfacial friction reduction by vanadium-containing oxides jointly contribute to the improvement in wear resistance. Higher carbide content and room-temperature hardness do not correspond to a lower high-temperature wear rate, and the high-temperature wear resistance of the coatings is affected by the oxidation behavior of the friction surface. \n\n \n
\n \n
\n
- \n \n \n \n \n \n
- \n \n \n \n \n
- \n \n \n \n
- \n \n \n \n
\n
\n 摘要
\n
\n
\n
\n
\n HTML全文
\n
\n
\n
\n
\n 参考文献(19)
\n
\n
\n
\n
\n
\n 相关文章
\n
\n
\n
\n
\n
\n
\n
\n
\n 施引文献
\n
\n
\n \n
\n
\n
\n
\n
\n
\n 资源附件(0)
\n
\n
\n
\n
下载:
\n\t\t\t\t