\n \n \n \n \n 铝合金电沉积焊接低温固相连接新方法 \n \n \t \n\t\n \n \n \n \n \n \n \n \n \n \n \n \n\t \n \n \n \n \n
\n
高级检索
\n
\n \n
\n
\n
\n
\n
\n \n \n
\n \n
\n \n
\n

铝合金电沉积焊接低温固相连接新方法

A novel electrodeposition welding method for low-temperature solid-state joining of aluminum alloys

\n \n \n \n \n \n
\n \n
\n \n \n
    \n \n \n
  • \n
    \n \n
    \n 摘要: \n 面向集成电路封装中铝合金结构件对低热损伤、超薄板可靠连接的迫切需求,基于电化学原理提出了电沉积焊低温固相连接新方法,通过在铝合金待连接界面驱动铜离子定向还原与沉积,实现了厚度为500 μm的6061-T6铝合金低温固相焊接.研究了坡口角度分别为45°与70°,水浴温度分别为20 ℃、30 ℃、40 ℃和50 ℃对接头成形的影响,并重点分析了20 ℃、30 ℃和40 ℃下接头的微观组织及力学性能.结果表明,电化学毛化预处理在待连接区域表面形成了纳米多孔氧化层,通过界面互锁效应提升了铜沉积区与铝母材的结合强度.70°坡口角度和30 ℃水浴温度下获得了无缺陷优质接头,焊缝区域由平均晶粒尺寸为0.71 ± 0.29 μm的细晶铜组织构成,并通过多孔氧化层与母材形成优异界面,铜沉积区平均硬度为195 HV,接头抗拉强度达到219 ± 3 MPa.实现了超薄板铝合金低温可靠连接,有利于实现集成电路轻量化基板的可靠连接. \n

     

    \n \n
    \n \n
    \n
    \n \n
    \n Abstract: \n In response to the urgent demand of aluminum alloy structural components in integrated circuit packaging for low-thermal-damage and reliable joining of ultra-thin sheets, a novel electrodeposition welding method for low-temperature solid-state joining was proposed based on electrochemical principles. By driving the directional reduction and deposition of copper ions at the aluminum alloy interfaces to be joined, low-temperature solid-state welding of 6061-T6 aluminum alloy with a thickness of 500 μm was achieved. The effects of groove angles of 45° and 70° and water bath temperatures of 20 ℃, 30 ℃, 40 ℃, and 50 ℃ on joint formation were investigated, and the microstructure and mechanical properties of the joints at 20 ℃, 30 ℃, and 40 ℃ were analyzed with particular emphasis. The results indicate that electrochemical texturing pretreatment forms a nanoporous oxide layer on the surfaces of the regions to be joined, which enhances the bonding strength between the copper deposition zone and the aluminum base metal through the interfacial mechanical interlocking effect. A defect-free, high-quality joint is obtained at a groove angle of 70° and a water bath temperature of 30 ℃. The weld zone consists of a fine-grained copper microstructure with an average grain size of 0.71 ± 0.29 μm and forms an excellent interface with the base metal through the porous oxide layer. The copper deposition zone exhibits an average hardness of 195 HV, and the tensile strength of the joint reaches 219 ± 3 MPa. Reliable low-temperature joining of ultra-thin aluminum alloy sheets is achieved, which is conducive to realizing the reliable joining of lightweight substrates in integrated circuit packaging. \n

     

    \n \n
    \n \n
    \n
  • \n
    \n \n \n
  • \n
  • \n \n \n \n \n
  • \n \n
  • \n \n \n \n \n
  • \n
  • \n \n \n \n \n
  • \n
  • \n \n \n \n \n
  • \n \n \n \n \n \n
  • \n
  • \n \n \n
\n \n
\n
\n \n
\n \n \n
\n
\n \n \n \n \n\t \n \n\t \n\t
\n\t\t \n\t\t
\n\t\t\t
\n\t\t\t\t \n\t\t\t
\n\t\t\t \n\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

\n\t\t\t\t\t

\n\t\t\t\t
\n\t\t\t
\n\t\t\t \n\t\t\t

\n\t\t\t\t/ \n\t\t\t

\n\t\t\t \n\t\t\t
\n\t\t\t\t下载:  \n\t\t\t\t全尺寸图片 幻灯片 \n\t\t\t
\n\t\t
\n\t\t \n\t\t
\n\t\t\t
\n\t\t\t\t \n\t\t\t
\n\t\t\t
\n\t\t\t\t
    \n \n \n\t\t\t\t
\n\t\t\t
\n\t\t\t
\n\t\t\t\t \n\t\t\t
\n\t\t
\n\t\t \n\t\t
\n\t\t\t 返回文章 \n\t\t\t \n\t\t
\n\t
\n \n\t \n\t \n\t \n\t \n\t
\n\t\t
\n\t\t\t返回 \n\t\t
\n\t
\n\t \n\t
\n\t
\n\t\t\t \n\t
\n\t
\n\t\t\t \n\t\t\t\t \n\t\t\t \n\t
\n\t
    \n\t \n\t
\n\t
\n\t \n\t\t\t\t \n\t\t\t \n\t
\n\t
\n \n\n\n \n \n\t
\n\t\t
\n\t\t\t \n\t\t
\n\t\t \n\t
\n
\n \n \n \n \n