\n
\n
\n
\n
\n
\n
\n
\n
\n
\n 超声振动作用下Inconel 690合金TIG熔敷层微观组织及力学性能研究
Study on microstructure and mechanical properties of Inconel 690 alloy TIG cladding layer under ultrasonic vibration
\n
\n
\n
\n
\n -
\n
\n
-
\n \n \n\n\n 摘要: \n 针对Inconel 690合金中高Ni-Cr成分在焊接时易产生晶界偏析严重及热裂纹等问题,设计了具备自动寻频功能的同轴复合超声-钨极惰性气体保护焊(ultrasonic-tungsten inert gas, U-TIG)焊接装备,并进行Inconel 690熔敷金属制备.同时,系统探究超声能量对熔覆层微观组织及力学性能的影响机理.结果表明,相比于传统TIG焊接,加入超声后,电弧发生收缩,焊缝熔宽增加,熔深降低,镍基合金湿润铺展获得大幅度提升.常规TIG熔敷层沿厚度方向存在明显组织差异,上部析出相相对较少,加入超声后,上部晶界处产生了细小的析出相,不同高度区域析出相分布趋于均匀.电子背散射衍射(electron backscatter diffraction, EBSD)结果表明,U-TIG熔覆层晶粒取向分布更均匀,平均晶粒尺寸减小43.06%,小角度晶界占比显著增加.熔覆层截面平均显微硬度从210.40 HV提升至247.30 HV,常温下抗拉强度从565 MPa提升至620.3 MPa,350 ℃高温下抗拉强度从484 MPa提升至536.86 MPa.超声的空化效应与声流效应的协同作用是改善熔覆层微观组织与力学性能的核心机理. \n\n \n
\n \n\n \n\n\n Abstract: \n To address the issues of severe grain boundary segregation and hot cracks that tend to occur during the welding of Inconel 690 alloy with high Ni-Cr content, coaxial hybrid ultrasonic-tungsten inert gas (U-TIG) welding equipment with an automatic frequency-searching function was designed, and Inconel 690 deposited metal was prepared. Meanwhile, the influence mechanism of ultrasonic energy on the microstructure and mechanical properties of the cladding layer was systematically investigated. The results indicate that compared with traditional TIG welding, the addition of ultrasound results in arc contraction, increased weld width, decreased weld depth, and a significant improvement in the wetting and spreading of the nickel-based alloy. The conventional TIG cladding layer exhibits significant microstructural differences along the thickness direction, with relatively fewer precipitated phases in the upper part. Upon the introduction of ultrasound, fine precipitated phases appear at the upper grain boundaries, and the distribution of precipitated phases tends to be more uniform across different height regions. The results of electron backscatter diffraction (EBSD) indicate that the grain orientation distribution in the U-TIG cladding layer is more uniform, with an average grain size reduction of 43.06% and a significant increase in the proportion of low-angle grain boundaries. The average microhardness of the cross-section of the cladding layer increases from 210.40 HV to 247.30 HV; the tensile strength at room temperature increases from 565 MPa to 620.3 MPa; the tensile strength at a high temperature of 350 ℃ increases from 484 MPa to 536.86 MPa. The synergistic effect of ultrasonic cavitation and acoustic streaming is the core mechanism for improving the microstructure and mechanical properties of the cladding layer. \n\n \n
\n \n
\n
- \n \n \n \n \n \n
- \n \n \n \n \n
- \n \n \n \n
- \n \n \n \n
\n
\n 摘要
\n
\n
\n
\n
\n HTML全文
\n
\n
\n
\n
\n 参考文献(37)
\n
\n
\n
\n
\n
\n 相关文章
\n
\n
\n
\n
\n
\n
\n
\n
\n 施引文献
\n
\n
\n \n
\n
\n
\n
\n
\n
\n 资源附件(0)
\n
\n
\n
\n
下载:
\n\t\t\t\t