高级检索

Ce含量对1000 MPa级高强钢埋弧焊熔敷金属组织的影响及演变规律

徐锴, 李春剑, 刘鑫, 喻朝飞, 郝乾宇, 王小刚, 赵江耀

徐锴, 李春剑, 刘鑫, 喻朝飞, 郝乾宇, 王小刚, 赵江耀. Ce含量对1000 MPa级高强钢埋弧焊熔敷金属组织的影响及演变规律[J]. 焊接学报, 2025, 46(6): 116-125. DOI: 10.12073/j.hjxb.20250227001
引用本文: 徐锴, 李春剑, 刘鑫, 喻朝飞, 郝乾宇, 王小刚, 赵江耀. Ce含量对1000 MPa级高强钢埋弧焊熔敷金属组织的影响及演变规律[J]. 焊接学报, 2025, 46(6): 116-125. DOI: 10.12073/j.hjxb.20250227001
XU Kai, LI Chunjian, LIU Xin, YU Zhaofei, HAO Qianyu, WANG Xiaogang, ZHAO Jiangyao. Effect of Ce content on microstructure and its evolution of deposited metal in submerged arc welding of 1000 MPa grade high strength steel[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2025, 46(6): 116-125. DOI: 10.12073/j.hjxb.20250227001
Citation: XU Kai, LI Chunjian, LIU Xin, YU Zhaofei, HAO Qianyu, WANG Xiaogang, ZHAO Jiangyao. Effect of Ce content on microstructure and its evolution of deposited metal in submerged arc welding of 1000 MPa grade high strength steel[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2025, 46(6): 116-125. DOI: 10.12073/j.hjxb.20250227001

Ce含量对1000 MPa级高强钢埋弧焊熔敷金属组织的影响及演变规律

详细信息
    作者简介:

    徐锴,学士,正高级工程师,博士生导师;主要研究方向为焊接材料和工艺;Email: xkwelding@163.com

  • 中图分类号: TG 423

Effect of Ce content on microstructure and its evolution of deposited metal in submerged arc welding of 1000 MPa grade high strength steel

  • 摘要:

    1000 MPa级高强钢在水电领域的应用已日趋成熟,但国内相应高性能焊材的研发较少,高强度熔敷金属保持低温高韧性是研发难点之一.通过添加Ce元素优化熔敷金属,并利用扫描电子显微镜(scanning electron microscope,SEM)、透射电子显微镜(transmission electron microscope,TEM)、高温激光共聚焦扫描显微镜(confocal laser scanning microscope,CLSM)等微观组织表征方法,研究了Ce含量对1000 MPa级高强钢埋弧焊熔敷金属组织强韧性及组织演变规律的影响.结果表明,Ce含量为0.02%时,抗拉和屈服强度分别提高3.7%和17.2%,此时强韧匹配效果最好,低温冲击韧性整体提升,Ce含量为0.01%时提升最大,−40 ℃和−60 ℃环境下分别为24.3%和42.2%.微观组织方面,Ce可细化晶粒,使M-A组元分布更弥散,增强组织韧性;含量为0.04%时会使块状铁素体和针状铁素体尺寸变大、大尺寸晶粒增多,影响抗拉强度.演变机理上,Ce与C协同富集引发晶格畸变促进M-A组元生成,含量为0.02%时使残余奥氏体含量增加,借助相变诱发塑性(transformationinduced plasticity,TRIP)效应提升塑性变形能力,促进下贝氏体转变实现强韧性协同提升;0.04%的Ce则导致晶界偏析加剧,形成含Ce脆性相析出物,降低奥氏体稳定性,使冲击韧性相对于0.02%时劣化.

    Abstract:

    The application of 1 000 MPa-grade high strength steel in the hydropower sector has become increasingly mature. However, the development of corresponding high-performance welding consumables in China remains limited. One of the key challenges in the research and development is maintaining high toughness at low temperatures in high-strength deposited metal. In this study, the deposited metal was optimized by adding Ce elements. Microstructural characterization methods, including SEM, TEM, and CLSM, were employed to investigate the effects of Ce content on the strength-toughness properties and microstructural evolution of the deposited metal in submerged arc welding of 1 000 MPa-grade high strength steel. The results indicate that when the Ce content is 0.02%, the tensile and yield strengths are increased by 3.7% and 17.2%, respectively, achieving the best balance between strength and toughness. The low-temperature impact toughness is generally enhanced, with the most significant improvement observed at a Ce content of 0.01%, showing increases of 24.3% and 42.2% at −40 °C and −60 °C, respectively. Microstructurally, Ce can refine grains, resulting in a more dispersed distribution of M-A constituents and enhancing the toughness of the microstructure. However, when the Ce content reaches 0.04%, the sizes of blocky ferrite and acicular ferrite increase, along with a higher proportion of large grains, adversely affecting the tensile strength. In terms of the evolution mechanism, the synergistic enrichment of Ce and C induces lattice distortion, promoting the formation of M-A constituents. At a Ce content of 0.02%, the residual austenite content increases, leveraging the TRIP effect to enhance plastic deformation capacity and facilitating the transformation of lower bainite, thereby achieving a synergistic improvement in strength and toughness. In contrast, a Ce content of 0.04% leads to exacerbated grain boundary segregation, the formation of Ce-containing brittle phase precipitates, and reduced austenite stability, resulting in a deterioration of impact toughness compared to that at a Ce content of 0.02%.

  • 近年来,中国大力推进和实施清洁能源战略,由于环保政策实施力度加大,民用和工业“煤改气”超出预期,2017年冬季中国遭遇大面积严重“气荒”. 根据中国石油集团经济技术研究院发布的《2018年国内外油气行业发展报告》,2018年中国天然气进口量达1254亿立方米,同比增长31.7%, 对外依存度45.3%. 基于国内对天然气实际需求情况,急需大量建设天然气输送管线、大型的石油、天然气储罐等国家重点工程项目. 建造液化天然气(liquefied natural gas,LNG)大型储罐可以大大降低天然气储运成本[1],解决中国天然气季节性供需矛盾. LNG低温储罐是其中的关键设备,一般由外罐、保冷层和内罐组成. 06Ni9DR钢具有焊接性能良好、强度高、−196 ℃低温韧性优异等特点[2],成为建造LNG储罐的首选材料. 然而这一材料前期主要依赖于进口. 2008年以来,鞍钢等国内钢铁企业积极进行低温用06Ni9DR钢的研发,并且最终研发成功,成果显著,冲破了国外对06Ni9DR钢的长期垄断,大力推动了国内LNG工业的发展进程. 而其焊接技术是LNG低温储罐建设核心技术之一. 06Ni9DR钢焊接过程中易出现的问题一般包括热裂纹、冷裂纹、电弧磁偏吹和低温韧性不足[3-4]. 目前,国内有关国产06Ni9DR 钢焊接热影响区(HAZ)的组织和性能的研究较少. 文中采用焊接热模拟的方法研究一次焊接热循环对06Ni9DR 钢HAZ组织和低温韧性的影响,为其焊接工艺的制定提供理论依据.

    试验用钢板是国内某著名钢厂生产的06Ni9DR钢,供货状态为淬火+回火(Quenching + tempering, QT). 奥氏体化温度790-850 ℃,冷却介质水. 回火温度540 ~ 600 ℃,冷却介质空气. 其化学成分如表1所示,测得的临界转变温度Ac1Ac3分别为615 ℃ 和702 ℃.

    表  1  06Ni9DR钢化学成分(质量分数,%)
    Table  1.  Chemical compositions of 06Ni9 steel
    CSiMnPSNi
    0.05 0.180 0.64 0.004 0.001 9.12
    AlV Cu Cr Mo Fe
    0.0250.004 0.038 0.031 0.005 余量
    下载: 导出CSV 
    | 显示表格

    采用Gleeble3500热模拟试验机再现HAZ的组织. 热模拟焊接条件为16 kJ/cm. 热模拟试样尺寸为80 mm × 10.5 mm × 10.5 mm. 热模拟参数如图1所示,四种峰值温度分别代表HAZ的粗晶区(1 350 ℃,CGHAZ)、细晶区(950 ℃,FGHAZ)、不完全淬火区(680 ℃,ICHAZ)和回火区(600 ℃,SCHAZ).

    图  1  焊接热模拟曲线
    Figure  1.  Schematic diagram of welding thermal cycles

    焊接热模拟试验后,采用标准V形缺口试样进行冲击试验,尺寸为55 mm × 10 mm × 10 mm,温度为−196 ℃. 用维氏硬度计测试硬度,扫描电镜(SEM)和背散射电子衍射(EBSD)观察显微组织及晶界,采用XRD测量残余奥氏体含量,按照五峰六线法和全谱拟合计算残余奥氏体的体积和质量分数,SEM观察冲击断口形貌.

    母材及HAZ的−196 ℃冲击吸收能量和硬度值如表2所示. 母材的冲击吸收能量为134 J,硬度值为247.3 HV10. HAZ的低温冲击韧性明显降低,说明HAZ整体发生了脆化. 峰值温度1 350 ℃粗晶区的冲击吸收能量最低,为母材的15.67%,21 J. 峰值温度950 ℃细晶区的冲击吸收能量最高,为108.3 J. 峰值温度680 ℃不完全淬火区的冲击吸收能量为105 J,较细晶区稍有降低. 峰值温度600 ℃的回火区冲击吸收能量为68.3 J,为母材的50.97%. 回火区的硬度为245.42 HV10,与母材相近. 除此之外,其余HAZ硬度相差不大,在340 HV10 ~ 350 HV10范围内,但与母材相比,提高了约100 HV10.

    表  2  母材及HAZ性能
    Table  2.  Properties of base metal and HAZ
    峰值温度Tp/℃冲击吸收能量AKV(−196℃)/J硬度H(HV10)
    母材134.0247.3
    135021.0340.0
    950108.3350.06
    680105.0342.56
    60068.3245.42
    下载: 导出CSV 
    | 显示表格

    母材和热模拟HAZ的组织如图2所示. 由图2a可见,母材06Ni9DR 钢的组织为回火马氏体和少量逆转奥氏体. 板条状马氏体分布在多边形原奥氏体晶内,逆转奥氏体主要分布在晶界上.

    图  2  扫描电镜组织形貌
    Figure  2.  SEM micrographs of base metal and simulated HAZ. (a) base metal; (b) 1350 ℃; (c) 950 ℃ ; (d) 680 ℃; (e) 600 ℃ (low power); (f) 600 ℃(high power)

    粗晶区加热温度远高于Ac3,金属属于严重过热状态,奥氏体晶粒迅速长大,因此,冷却过程中晶粒粗大的奥氏体转变为晶粒粗大的板条马氏体,还有少量的残余奥氏体(图2b). 细晶区加热温度略高于Ac3,奥氏体晶粒细小,在冷却过程中,晶粒细小的奥氏体转变为晶粒细小的马氏体以及少量的残余奥氏体(图2c). 不完全淬火区加热温度处于Ac1和Ac3之间,只有部分马氏体转变为奥氏体. 由于加热时间短,加热温度不高,Ni等化学元素不能快速扩散,导致形成的奥氏体不能快速长大. 而少量未转变的马氏体继续长大,因此室温组织为晶粒尺寸不均匀的马氏体和残余奥氏体(图2d). 由图2e可见,回火区加热温度在MsAc1之间,由马氏体直接切变生成逆转奥氏体,是非扩散型转变产物. 由于组织中C,Ni,Mn等稳定奥氏体元素聚集量较高,热稳定性很高,常温中能够稳定存在,主要分布在原奥氏体晶界、马氏体束界[5]、马氏体板条间. 高倍观察(图2f),大块逆转奥氏体在冷却过程中又形成二次板条马氏体. 回火区的组织为回火马氏体和逆转奥氏体.

    图3为HAZ含有晶界的EBSD欧拉取向图和晶界角度图,蓝色为3° ~ 15°小角度晶界,绿色为15° ~ 45°大角度晶界,黄色为大于 45°有效大角度晶界. 可见,粗晶区的原奥氏体晶界主要为15° ~ 45°的大角度晶界,晶界内部不同取向板条束之间为黄色有效大角度晶界,取向差较小的板条之间为小角度晶界(图3b). 细晶区的晶粒呈多边形块状,且细化明显(图3c). 未完全淬火区晶粒大小较不均匀(图3d). 回火区的原奥氏体晶粒较母材无明显变化(图3e). 如图3f所示,45°以上有效大角度晶界含量分别为母材21.7%,粗晶区14.4%,细晶区24.4%,不完全淬火区33.5%,回火区23.1%.母材及HAZ马氏体相晶粒内部局域取向差分布如图4所示. 母材的局域取向差峰值在0.45°,粗晶区的局域取向差峰值为1.55°,细晶区和回火区的均为0.55°,不完全淬火区的取向差峰值为0.35°. 说明母材及HAZ晶粒内部存在着不均匀的位错密度堆积,除粗晶区以外三个区的位错密度低、产生的位错滑移运动较少,塑性较好[6].

    图  3  EBSD欧拉图和晶界角度分布
    Figure  3.  EBSD Euler graphs and local misorientation distribution.(a) base metal; (b) 1350 ℃; (c) 950 ℃; (d) 680 ℃; (e) 600 ℃; (f) grain boundary angle distribution
    图  4  局域取向差分布
    Figure  4.  Local misorientation distribution

    母材及HAZ奥氏体含量如表3所示. 由于奥氏体与马氏体密度不同,计算出的质量分数与体积分数在数值上有所差距,但是变化趋势相同. 相对母材,粗晶区奥氏体的含量与其相近,细晶区较之略有降低,不完全淬火区和回火区的奥氏体含量相对提高.

    表  3  母材及HAZ奥氏体含量
    Table  3.  Austenite content of base metal and HAZ
    峰值温度Tp/℃奥氏体体积分数V(%)奥氏体质量分数w(%)
    母材 1.97 0.90
    1350 1.95 0.88
    950 1.88 0.63
    680 3.10 1.28
    600 2.60 1.20
    下载: 导出CSV 
    | 显示表格

    母材断口包括纤维区、放射区和剪切唇. 放射区有细小的河流花样和撕裂棱,为准解理断裂(图5a). 粗晶区(图5b)宏观断口平齐,几乎无塑性变形,纤维区及剪切唇基本消失,几乎全部为放射区,且该区无表征微小塑性变形的放射线花样,呈现闪光小面组成的结晶状断口形貌. 另外,可见一系列取向不同的平坦、光滑的解理小刻面. 这些小刻面尺寸大致相当于马氏体束大小. 每个小刻面上有解理台阶、河流花样、二次裂纹等特征,为解理断裂. 细晶区(图5c)和不完全淬火区(图5d)断口类似,主要由纤维区、较小的放射区与剪切唇组成. 放射区由细小且浅的韧窝、河流花样组成,为准解理断裂. 回火区(图5e)断口纤维区较小,主要由放射区与剪切唇组成. 放射区为准解理断裂与二次裂纹特征,可见撕裂棱、河流花样和解理面.

    图  5  断口形貌
    Figure  5.  Fracture morphology. (a) base metal; (b)1350 ℃; (c) 950 ℃; (d) 680 ℃; (e) 600 ℃

    表2可见,06Ni9DR 钢HAZ-196 ℃的冲击能量明显低于母材,HAZ整体发生了脆化. 粗晶区脆化最为明显,其次是回火区. HAZ脆化与组织、晶粒大小、大小角度晶界和位错密度等密切相关. HAZ的组织为马氏体或回火马氏体和少量的残余或逆转奥氏体(图2). 45°以上有效大角度晶界含量为680 ℃ > 950 ℃ > 600 ℃ > 母材 > 1350 ℃(图3f). 局域取向差峰值(位错密度)为1350 ℃ > 950 ℃、600 ℃ > 母材 > 680 ℃(图4). 一般来说,有效大角度晶界越多[7-8],位错密度越低,材料韧性越好. 残余或逆转奥氏体的数量、形态和分布直接影响HAZ的低温冲击功.

    粗晶区脆化的原因包括以下几个方面:一是原始奥氏体晶粒粗大[9-11]. 经计算粗晶区的晶粒平均直径超过100 μm,根据Hall-Petch公式,晶粒直径越大,裂纹扩展临界应力增量越小,韧性越低. 另外,有效大角度晶界一般分布于原奥氏体晶界和板条束界,晶粒粗大使得有效大角度晶界较少. 而大角度晶界能够阻碍裂纹的扩展,使裂纹发生钝化而产生分支,从而消耗能量,增大韧性[10]. 二是位错密度较大,导致位错缠结、交割,使其运动阻力增大,韧性降低. 三是粗大板条马氏体的存在. 板条马氏体的板条平直细长,平行排列方向性强,解理裂纹在马氏体的板条束中可连续无阻碍贯穿,导致韧性降低[12]. 四是残余奥氏体少且不稳定. 06Ni9DR 钢具有良好的低温韧性是因为逆转奥氏体的存在. 逆转奥氏体是马氏体回火时切变产生的,而残余奥氏体是马氏体相变结束剩余的过冷奥氏体. 前者含有C,Ni,Mn等奥氏体稳定元素,−196 ℃时稳定性较高,可提高材料的韧性. 后者储存能量较高,不稳定,相对于逆转奥氏体更容易转变,对低温韧性贡献较小[13].

    细晶区的有效大角度晶界和位错密度稍高于母材,残余奥氏体量稍低于母材,但其韧性远低于且硬度远高于母材. 分析认为原因可能有两个方面:一是,细晶区的马氏体为淬火马氏体,相对母材的回火马氏体,其过饱和度、内应力较大,导致塑性低而硬度高. 二是,残余奥氏体的韧化效果低于逆转奥氏体[13]. 细晶区的硬度和韧性高于其它HAZ,主要是细晶强化的结果.

    不完全淬火区的有效大角度晶界和残余奥氏体量高于母材,位错密度低于母材,但其韧性值和硬度值与细晶区相近,韧性低于母材,硬度高于母材. 导致其韧性低于母材的原因与细晶区类似,主要是淬火马氏体和残余奥氏体的存在. 另外,晶粒大小不均匀,尤其是粗大马氏体的存在也是导致韧性降低的重要因素. 需要指出的是不完全淬火区的残余奥氏体的含量远高于母材,但韧性远低于母材,这进一步说明残余奥氏体稳定性较差,对低温韧性的贡献较小[13].

    回火区的有效大角度晶界和取向差峰值稍高于母材,逆转奥氏体量远高于母材,但其韧性远低于母材. 这主要是因为母材中原有的逆转奥氏体经过600 ℃二次回火作用,C,Ni元素继续扩散,向晶界处的逆转奥氏体聚集,原逆转奥氏体继续长大,并不断生成新的逆转奥氏体,沿晶界密集呈链状分布,降低了原奥氏体晶界的结合力,为裂纹扩展提供了通道. 另外,晶界存在的部分大块奥氏体在回火过程中转变成二次板条马氏体(图2f),形成M-A组元,也会导致韧性降低[14].

    (1) 06Ni9DR 钢粗晶区和回火区的冲击吸收能量分别为母材的15.67%和50.97%. 细晶区和不完全脆化区的冲击吸收能量相近,分别为母材的80.82%和78.36%.

    (2) 粗晶区断口为解理断裂,脆化原因主要为原始奥氏体晶粒粗大及其导致的有效大角度晶界较少,残余奥氏体量少且不稳定,以及较大的位错密度和粗大马氏体的存在.

    (3) 回火区断口为准解理断裂,其脆化的主要原因是晶界呈链状分布的大块逆转奥氏体和M-A组元的存在.

    (4) 细晶区和不完全淬火区的断口均为准解理断裂. 淬火马氏体的存在和残余奥氏体的低温稳定性差导致两区韧性低于母材. 另外,晶粒大小不均匀也会导致不完全淬火区韧性降低.

  • 图  1   焊接试板示意图(mm)

    Figure  1.   Schematic diagram of welding test plate

    图  2   取样位置示意图

    Figure  2.   Schematic diagram of sampling location

    图  3   不同Ce含量熔敷金属强度与韧性

    Figure  3.   Strength and toughness of deposited metal with different rare earth contents

    图  4   各尺寸晶粒数量占比

    Figure  4.   Proportion of grain quantities by size

    图  5   不同Ce含量1000 MPa级高强钢熔敷金属显微组织

    Figure  5.   Microstructure of 1000 MPa grade high strength steel deposited metal with different Ce contents. (a) OM of 0% Ce; (b) OM of 0.02% Ce; (c) OM of 0.04% Ce; (d) SEM of 0% Ce; (e) SEM of 0.02% Ce; (f) SEM of 0.04% Ce

    图  6   不同Ce含量1000 MPa级高强钢熔敷金属的EBSD取向图像

    Figure  6.   EBSD orientation images of deposited metal for 1000 MPa grade high strength steel with different Ce contents. (a) 0% Ce; (b) 0.02% Ce; (c) 0.04% Ce

    图  7   不同Ce含量1000 MPa级高强钢熔敷金属相区分EBSD图

    Figure  7.   EBSD phase-distinguished maps of deposited metal for 1000 MPa grade high strength steel with different Ce contents. (a) 0% Ce; (b) 0.02% Ce; (c) 0.04% Ce

    图  8   不同含量1000 MPa级高强钢熔敷金属奥氏体组织TEM

    Figure  8.   TEM microstructures of deposited metal for 1000 MPa grade high strength steel with different Ce additions. (a) 0% Ce; (b) 0.02% Ce; (c) 0.04% Ce

    图  9   不同含量1000 MPa级高强钢熔敷金属AF组织TEM

    Figure  9.   TEM microstructures of deposited metal for 1000 MPa grade high strength steel with different Ce additions. (a) 0% Ce; (b) 0.02% Ce; (c) 0.04% Ce

    图  10   不同含量Ce元素在奥氏体晶界处的分布

    Figure  10.   Distribution of Ce element with different contents at austenite grain boundaries. (a) 0.02% Ce;(b) 0.04% Ce

    图  11   不同Ce含量的1000 MPa级高强钢熔敷金属组织演变高温金相观察

    Figure  11.   High-temperature metallographic observation of microstructure evolution of deposited metal in 1000 MPa-grade high-strength steel with different Ce contents. (a) 0%Ce T = 1 403.1 ℃;(b) 0%Ce T = 689.6 ℃;(c) 0%Ce T = 689.6 ℃;(d) 0.02%Ce T = 1 401.5 ℃;(e) 0.02%Ce T = 716.8 ℃;(f) 0.02%Ce T = 449.8 ℃;(g) 0.04%Ce T = 1 390.6 ℃;(h) 0.04%Ce T = 699.2 ℃;(i) 0.04%Ce T = 480.5 ℃

    图  12   不同含量Ce元素的同步热分析结果

    Figure  12.   Differential thermal analysis results of samples with different contents of Ce element

    图  13   不同Ce含量的1000 MPa级高强钢熔敷金属贝氏体形核规律观察

    Figure  13.   Observation of bainite nucleation behavior in deposited metal of 1 000 MPa-grade high-strength steel with different Ce contents. (a) 0%Ce T = 425.3 ℃;(b) 0.02% Ce T = 418.2 ℃;(c) 0.04% Ce T = 431.2 ℃

    表  1   焊接工艺参数

    Table  1   Welding experiment paraments

    焊接电流
    I/A
    电弧电压
    U/V
    焊接速度
    v/(cm·min−1)
    层间温度
    T0/℃
    后热温度
    T1/℃
    4503240≤200350
    下载: 导出CSV

    表  2   熔敷金属的化学成分(质量分数,%)

    Table  2   Chemical compositions of deposited metal

    C Si Mn P S Cr Ni Mo Ce Fe
    0.08 0.15 1.8 0.01 0.003 0.5 2.7 0.7 0 余量
    0.08 0.15 1.8 0.01 0.003 0.5 2.7 0.7 0.01 余量
    0.08 0.15 1.8 0.01 0.003 0.5 2.7 0.7 0.02 余量
    0.08 0.15 1.8 0.01 0.003 0.5 2.7 0.7 0.04 余量
    下载: 导出CSV

    表  3   不同Ce含量熔敷金属力学性能

    Table  3   Mechanical properties of deposited metal with different rare earth contents

    Ce含量ωCe
    (质量分数, %)
    抗拉强度
    Rm/MPa
    屈服强度
    Rp0.2/MPa
    断后伸长率
    A(%)
    −40 ℃冲击吸收能量
    KV2/J
    −60 ℃冲击吸收能量
    KV2/J
    0 935 740 16.0 87、86、86 53、59、61
    0.01 930 820 19.0 103、106、89 81、82、82
    0.02 960 867 15.5 86、104、93 74、80、78
    0.04 885 803 18.5 85、81、71 72、69、73
    下载: 导出CSV
  • [1]

    LI X Z, CHEN Z J, FAN X C, et al. Hydropowerdevelopment situation and prospects in China[J]. Renewable and Sustainable Energy Reviews, 2018, 82: 232 − 239. doi: 10.1016/j.rser.2017.08.090

    [2]

    PéREZ-DíAZ J I, CHAZARRA M, GARCíA-GONZáLEZ J, et al. Trendsand challenges in the operation of pumped-storagehydropower plants[J]. Renewable and Sustainable EnergyReviews, 2015, 44: 767 − 784. doi: 10.1016/j.rser.2015.01.029

    [3]

    HORIKAWA K, WATANABE N. Application of extra-high tensile strength steel for hydropower plants[J]. Welding in the World: Journal of the International Institute of Welding: Journal of the International Institute of Welding, 2008, 52: 3-1 − 3-8.

    [4]

    HARA N, SATO M. Development and application of weldingconsumables for 950 MPa class high strength steels [C]//Conference on High Strength Steels for Hydropower Plants, Takasaki, Japan, 2009.

    [5]

    KIPPENHAN N, GSCHNEIDNER Jr K A. RARE-EARTH METALS IN STEELS[R]. Iowa State Univ. of Science and Technology, Ames. Rare-Earth Information Center, 1970.

    [6]

    PREINFALK C, MORTEANI G. The industrial applications of rare earth elements[C]//Lanthanides, Tantalum and Niobium: Mineralogy, Geochemistry, Characteristics of Primary Ore Deposits, Prospecting, Processing and Applications Proceedings of a workshop in Berlin, November 1986. Springer Berlin Heidelberg, 1989: 359 − 370.

    [7] 李春龙. 稀土在钢中应用与研究新进展[J]. 稀土, 2013, 34(3): 78 − 85.

    LI Chunlong. New progress in the application and research of rare earth in steel[J]. Chinese Rare Earths, 2013, 34(3): 78 − 85.

    [8] 王力锋, 刘凤德, 张宏, 等. 氧化铈对高强钢复合焊接焊缝组织与韧性的影响[J]. 机械工程学报, 2016, 52(22): 70 − 77. doi: 10.3901/JME.2016.22.070

    WANG Lifeng, LIU Fengde, ZHANG Hong, et al. Effect of cerium oxide on the microstructure and toughness of hybrid welding joints of high-strength steel[J]. Journal of Mechanical Engineering, 2016, 52(22): 70 − 77. doi: 10.3901/JME.2016.22.070

    [9] 孟祥海, 王伟, 毕胜, 等. Ce/Ce-Zr夹杂物诱导高强船板钢中针状铁素体形核行为的研究[J]. 钢铁钒钛, 2022, 43(2): 146 − 151. doi: 10.7513/j.issn.1004-7638.2022.02.022

    MENG Xianghai, WANG Wei, BI Sheng, et al. Study on nucleation behavior of acicular ferrite induced by Ce/Ce-Zr inclusions in high-strength ship plate steel[J]. Iron and Vanadium Titanium, 2022, 43(2): 146 − 151. doi: 10.7513/j.issn.1004-7638.2022.02.022

    [10] 臧若愚, 李晶, 黄飞. 稀土Ce对高强工程机械用钢夹杂物和高温塑性的影响[J]. 有色金属科学与工程, 2024, 15(3): 449 − 456.

    ZANG Ruoyu, LI Jing, HUANG Fei. Effect of rare earth Ce on inclusions and high temperature ductility of high-strength engineering machinery steel[J]. Nonferrous Metals Science and Engineering, 2024, 15(3): 449 − 456.

    [11] 郜慧敏, 方琪, 孙伟. 稀土La对C-Mn-Si钢静态软化行为的影响[J]. 世界有色金属, 2017(11): 267 − 269.

    GAO Huimin, FANG Qi, SUN Wei. Effect of rare earth La on static softening behavior of C-Mn-Si steel[J]. World Nonferrous Metals, 2017(11): 267 − 269.

    [12] 勤牧, 杨雄, 杨维宇. 包钢含稀土Q690CF高强钢的研制[J]. 包钢科技, 2020, 46(2): 52 − 55. doi: 10.3969/j.issn.1009-5438.2020.02.016

    QIN Mu, YANG Xiong, YANG Weiyu. Development of rare earth-containing Q690CF high-strength steel at baogang[J]. Science & Technology of Baotou Steel, 2020, 46(2): 52 − 55. doi: 10.3969/j.issn.1009-5438.2020.02.016

    [13] 冯伟, 于庭祥, 徐锴, 等. 1 000 MPa级高强钢埋弧焊熔敷金属组织及性能[J]. 焊接, 2023(11): 6 − 12. doi: 10.12073/j.hj.20230706001

    FENG Wei, YU Tingxiang, XU Kai, et al. Microstructure and properties of submerged arc welding deposit metal for 1000 MPa grade high-strength steel[J]. Welding & Joining, 2023(11): 6 − 12. doi: 10.12073/j.hj.20230706001

    [14] 于彦冲, 陈伟庆, 郑宏光. 铈及混合稀土对Fe-36Ni低膨胀合金凝固组织的影响[J]. 中国稀土学报, 2012, 30(2): 175 − 180. doi: 10.1016/S1002-0721(12)60018-0

    YU Yanchong, CHEN Weiqing, ZHENG Hongguang. Effect of cerium and mixed rare earths on the solidification structure of Fe-36Ni low-expansion alloy[J]. Journal of Rare Earths, 2012, 30(2): 175 − 180. doi: 10.1016/S1002-0721(12)60018-0

    [15] 刘朋. 稀土在相变诱发塑性钢中的组织细化与微合金化效应研究[D]. 合肥: 中国科学技术大学, 2024.

    LIU Peng. Study on the microstructure refinement and microalloying effect of rare earth in transformation-induced plasticity steels [D]. Hefei: University of Science and Technology of China, 2024.

    [16] 蔡恒君. 1000 MPa以上级别汽车用冷轧高强钢超快冷物理冶金行为及变形特性研究[D]. 北京: 北京科技大学, 2018.

    CAI Hengjun. Study on the ultrafast cooling physical metallurgy behavior and deformation characteristics of cold-rolled high-strength steel for automotive applications with a strength level above 1000 MPa [D]. BeiJing: University of Science and Technology Beijing, 2018.

    [17] 王龙妹. 稀土在低合金及合金钢中的应用[M]. 北京: 冶金工业出版社, 2016.

    WANG Longmei. Application of rare earths in low-alloy and alloy steels [M]. Beijing: Metallurgical Industry Press, 2016.

    [18]

    SOLEIMANI M, KALHOR A, MIRZADEH H. Transformation-induced plasticity (TRIP) in advanced steels: A review[J]. Materials Science & Engineering A, 2020, 795(9): 140023.

    [19]

    LIU P, HOU X, YANG C, et al. Tailoring microstructure evolution and austenite stability of TRIP steels by Rare-Earth micro-alloying[J]. Materials Characterization, 2023, 203: 1 − 16. doi: 10.1016/j.matchar.2023.113035

    [20] 冯伟, 于庭祥, 陈波, 等. Cr含量对 1000 MPa级高强钢熔敷金属组织演变的作用机制[J]. 焊接学报, 2024, 45(9): 76 − 83. doi: 10.12073/j.hjxb.20240409001

    FENG Wei, YU Tingxiang, CHEN Bo, et al. Mechanism of the effect of Cr content on the microstructure evolution of deposited metal in 1000 MPa grade high-strength steel[J]. Transactions of the China Welding Institution, 2024, 45(9): 76 − 83. doi: 10.12073/j.hjxb.20240409001

    [21]

    JIANG Y Y, WANG Z D, DENG X T, et al. Effect of cerium addition on the bainite transformation behavior of medium carbon microalloyed steel[J]. Materials Research Express, 2019, 6(10): 106526. doi: 10.1088/2053-1591/ab36f8

    [22]

    HSU T Y. Effects of rare earth element on isothermal and martensitic transformations in low carbon steels[J]. Transactions of the Iron & Steel Institute of Japan, 2007, 38(11): 1153 − 1164.

    [23] 梁益龙, 谭起兵, 李光新, 等. 不同稀土含量的GDL-1钢中贝氏体相变研究[J]. 兵器材料科学与工程, 2008(3): 31 − 34. doi: 10.3969/j.issn.1004-244X.2008.03.008

    LIANG Yilong, TAN Qibing, LI Guangxin, et al. Study on bainitic transformation in GDL-1 steel with different rare earth contents[J]. Ordnance Material Science and Engineering, 2008(3): 31 − 34. doi: 10.3969/j.issn.1004-244X.2008.03.008

    [24]

    CAI G J, LI C S. Effects of Ce on inclusions, microstructure, mechanical properties, and corrosion behavior of AISI 202 stainless steel[J]. Journal of Materials Engineering & Performance, 2015, 24(10): 3989 − 4009.

    [25]

    WANG Y J, CHEN J G, YANG J, et al. Effect of La2O3 on granular bainite microstructure and wear resistance of hardfacing layer metal[J]. Journal of Rare Earths, 2014, 32(1): 83 − 89. doi: 10.1016/S1002-0721(14)60036-3

图(13)  /  表(3)
计量
  • 文章访问数:  34
  • HTML全文浏览量:  8
  • PDF下载量:  8
  • 被引次数: 0
出版历程
  • 收稿日期:  2025-02-26
  • 网络出版日期:  2025-05-15
  • 刊出日期:  2025-06-24

目录

/

返回文章
返回