高级检索

TC21 + TC4-DT线性摩擦焊接头组织与力学性能试验

张传臣, 张田仓, 金俊龙

张传臣, 张田仓, 金俊龙. TC21 + TC4-DT线性摩擦焊接头组织与力学性能试验[J]. 焊接学报, 2019, 40(12): 133-137. DOI: 10.12073/j.hjxb.2019400326
引用本文: 张传臣, 张田仓, 金俊龙. TC21 + TC4-DT线性摩擦焊接头组织与力学性能试验[J]. 焊接学报, 2019, 40(12): 133-137. DOI: 10.12073/j.hjxb.2019400326
ZHANG Chuanchen, ZHANG Tiancang, JIN Junlong. Microstructure and mechanical properties of linear friction welding joint of TC21/TC4-DT[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(12): 133-137. DOI: 10.12073/j.hjxb.2019400326
Citation: ZHANG Chuanchen, ZHANG Tiancang, JIN Junlong. Microstructure and mechanical properties of linear friction welding joint of TC21/TC4-DT[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(12): 133-137. DOI: 10.12073/j.hjxb.2019400326

TC21 + TC4-DT线性摩擦焊接头组织与力学性能试验

Microstructure and mechanical properties of linear friction welding joint of TC21/TC4-DT

  • 摘要: 针对高强TC21和中强TC4-DT异种钛合金进行线性摩擦焊工艺研究,对接头进行不同热处理,接头微观组织和力学性能进行试验分析. 结果表明,TC21 + TC4-DT线性摩擦焊接头飞边成形良好,飞边表面光滑根部无明显缺陷存在;焊态条件下焊缝组织为典型的魏氏组织结构特征,热处理后焊缝组织析出弥散的针状α相,随着热处理温度的升高析出的针状α相逐渐长大粗化,致使接头冲击和断裂性能先上升后下降;接头拉伸性能与TC4-DT母材相当;700℃/3 h热处理接头、母材高周疲劳性能试验结果表明,接头的疲劳极限达到558 MPa,与TC4-DT基体相当,焊缝组织细化是提高接头疲劳极限的重要原因.
    Abstract: High strength TC21 and medium strength TC4-DT Ti-alloys with dissimilar damage tolerance were linear friction welded (LFW). Different heat treatments were selected for the joints. The microstructure and mechanical properties of the welded joints were studied after heat treatment. The results showed that good flash is formed on both side of the base metal after LFW. The surface of the flash is smooth and no defects are found at the root of the flash. The microstructure of the weld zone (WZ) is widmanstatten in as-welded condition. Precipitated acicular α phase is distributed in the weld zone after heat treatment. With heat treatment temperature increasing the precipitated α phases are coarsened. The impact properties and fracture toughness properties rises at the first and goes down latter with α coarsened. Tensile strength of the joints is equal to TC4-DT base metal. The high cycle fatigue limit of the joint is 558MPa at the temperature of 700℃ for 3 hours which is equal to TC4-DT base metal. Due to the fine microstructure of WZ the fatigue limit increases.
  • [1] Vairis A, Frost M. Modelling the linear friction welding of titanium blocks[J]. Materials Science and Engineering A, 2000, 292(1):8-17.
    [2] Vairis A, Frost M. High frequency linear friction welding of a titanium alloy[J]. Wear, 1998, 217(1):117-131.
    [3] 曹京霞, 黄 旭, 李臻熙. TA15钛合金的高周疲劳性能和断裂特征[J]. 材料工程, 2004(3):28-30
    Cao Jingxia, Huang Xu, Li Zhenxi. High cycle fatigue properties and fracture features of TA15 titanium alloy[J]. 2004(3):28-30
    [4] 高灵清, 朱金华. TA5钛合金焊板的疲劳断口分析[J]. 金属热处理, 2006, 31(8):91-92
    Gao Lingqing, Zhu Jinhua. Analysis on fatigue fractures of TA5 alloy welded plates[J]. Heat Treatment of Metals, 2006, 31(8):91-92
    [5] Bhamji I, Preuss M, Threadgill P L. Solid state joining of metals by linear friction welding:a literature review[J]. Materials Science and Technology, 2011, 27(1):2-12.
    [6] Wanjara P, Jahazi M. Linear friction welding of Ti-6Al-4V:processing, microstructure, and mechanical-property inter-relationships[J]. Metallurgical and Materials Transactions, 2005, 36A(8):2149-2164.
    [7] 张传臣, 张田仓, 季亚娟, 等. 线性摩擦焊接头形成过程及机理[J]. 材料工程, 2012, 43(11):39-43
    Zhang Chuanchen, Zhang Tiancang, Ji Yajuan, et al. Formation process and mechanism of linear friction welding joint[J]. Journal of Materials Engineering, 2012, 43(11):39-43
    [8] 张传臣, 黄继华, 张田仓, 等. 异质钛合金线性摩擦焊接头微观组织与显微硬度分析[J]. 焊接学报, 2012, 33(4):97-100
    Zhang Chuanchen, Huang Jihua, Zhang Tiancang, et al. Investigation on microstructure and microhardness of linear friction welded joints of dissimilar titanium alloys[J]. Transactions of the China Welding institution, 2012, 33(4):97-100
    [9] Zhang C C, Zhang T C, Ji Y J, et al. Effects of heat treatment on microstructure and microhardness of linear friction welded dissimilar Ti alloys[J]. Transactions of Nonferrous Metals Society of China, 2013, 13:3540-3544.
    [10] 马少俊, 吴学仁, 刘建中, 等. TC21钛合金的微观组织对力学性能的影响[J]. 航空材料学报, 2006, 26(5):22-25
    Ma Shaojun, Wu Xueren, Liu Jianzhong, et al. Influence of microstructures on mechanical properties for TC21 titanium alloy[J]. Journal of Aeronautical Materials, 2006, 26(5):22-25
    [11] 祝力伟, 王新南, 朱知寿. 不同热处理工艺下TC4-DT 钛合金的显微组织及力学性能[J]. 钛工业进展, 2011, 29(1):9-12
    Zhu Liwei, Wang Xinnan, Zhu Zhishou. Effect of heat treatment on microstructure and mechanical properties of TC4-DT alloy[J]. Titanium Industry Process, 2011, 29(1):9-12
  • 期刊类型引用(1)

    1. 王兴磊,杨赫然,孙兴伟,赵泓荀,潘飞. 基于WOA-RBF的螺杆转子双砂带磨削表面粗糙度及材料去除率预测. 制造技术与机床. 2025(04): 172-179 . 百度学术

    其他类型引用(8)

计量
  • 文章访问数:  266
  • HTML全文浏览量:  8
  • PDF下载量:  46
  • 被引次数: 9
出版历程
  • 收稿日期:  2019-04-10

目录

    /

    返回文章
    返回