高级检索

超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

房卫萍, 肖铁, 张宇鹏, 徐望辉, 易耀勇

房卫萍, 肖铁, 张宇鹏, 徐望辉, 易耀勇. 超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性[J]. 焊接学报, 2019, 40(12): 121-128. DOI: 10.12073/j.hjxb.2019400324
引用本文: 房卫萍, 肖铁, 张宇鹏, 徐望辉, 易耀勇. 超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性[J]. 焊接学报, 2019, 40(12): 121-128. DOI: 10.12073/j.hjxb.2019400324
shu
FANG Weiping, XIAO Tie, ZHANG Yupeng, Xu Wanghui, YI Yaoyong. Stress corrosion crack sensitivity of ultra-thick TC4 titanium alloy electron beam welding joints[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(12): 121-128. DOI: 10.12073/j.hjxb.2019400324
Citation: FANG Weiping, XIAO Tie, ZHANG Yupeng, Xu Wanghui, YI Yaoyong. Stress corrosion crack sensitivity of ultra-thick TC4 titanium alloy electron beam welding joints[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(12): 121-128. DOI: 10.12073/j.hjxb.2019400324
shu

超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

  • 1.

    广东省焊接技术研究所(广东省中乌研究院) 广东省现代焊接技术重点实验室, 广州 510650

  • 2.

    中国科学院金属研究所, 沈阳 110016

基金项目: 广州市项目（201907010010，201807010036）；广东省科技项目（2018B090904004，2017A070701026，2016B070701025，2014B070705007）；攀钢集团项目（2014外协03）

Stress corrosion crack sensitivity of ultra-thick TC4 titanium alloy electron beam welding joints

  • 1.

    Guangdong Provincial Key Laboratory of Advanced Welding Technology, Guangdong Welding Institute, Guangzhou 510650, China

  • 2.

    Institute of Metal Research Chinese Academy of Sciences, Shenyang 110016, China

摘要

    摘要
  • 摘要: 针对100 mm超厚板TC4钛合金电子束焊接接头，采用慢应变速率拉伸方法评价接头在人造海水中的应力腐蚀敏感性，分析接头的显微组织和断口形貌，对接头的腐蚀机制进行研究. 结果表明，室温条件下应变速率为ε=1×10-6 s-1时，母材在海水中未表现出应力腐蚀敏感性；焊缝上部、中部和下部具有轻微应力腐蚀敏感性. 焊缝在海水中发生阳极溶解，产生氢吸附，导致裂纹的萌生. 同时氢扩散诱导α'相界及α'相内发生位错塞积，进而使裂纹在更低的应力水平下发生扩展.
    Abstract: Slow strain rate tensile method was adopted to evaluate the stress corrosion crack (SCC) sensitivity of 100 mm ultra-thick TC4 titanium alloy electron beam welded (EBW) joints under artificial seawater. The corrosion mechanism was studied by observing the microstructure and fracture morphology of the joint. The results showed that the base metal have no SCC sensitivity in seawater. However, the upper, middle and lower parts of the weld showed slight SCC sensitivity at room temperature under the condition of strain rate ε=1×10-6 s-1. In seawater, anodic dissolution accursed in the weld metal, which increased the Ti ion concentration in the solution at the crack tip, then, H atoms are evolved and absorbed at the crack tip. The diffused hydrogen then promotes dislocation emission and increases the dislocation density at the α' phase boundaries and in the α' phase. The crack initiation and propagation are results of the accumulation of highly hydrogen. At the same time, hydrogen enhances mobility of dislocations, then the crack propagates at a lower stress level.
    • HTML全文
    • 参考文献(24)
  • [1] Lütjering G, Williams J C. Titanium[M]. 2nd ed. New York:Springer Berlin Heidelberg, 2007.
    [2] 赵永庆. 我国创新研制的主要船用钛合金及其应用[J]. 中国材料进展, 2014, 33(7):398-404
    Zhao Yongqing. The new main titanium alloys used for shipbuilding developed in China and their applications[J]. Materials China, 2014, 33(7):398-404
    [3] 常 辉. 钛材料在海洋工程中的应用[N]. 北京:中国有色金属报, 2018.
    [4] 赵凤桐. 钛及钛合金在氯碱工业上的应用[J]. 氯碱工业, 1991, 6:33-42
    Zhao Fengtong. Application of titanium and titanium alloys in chlor-alkali industry[J]. Chlor-Alkali Industry, 1991, 6:33-42
    [5] 余存烨. 耐蚀钛合金的发展[J]. 钛工业进展, 2003, 20(1):12-19
    Yu Cunye. Development of corrosion resistant titanium alloys[J]. Titanium Industry Progress, 2003, 20(1):12-19
    [6] Atapour M, Pilchak A L, Shamanian M, et al. Corrosion behavior of Ti-8Al-1Mo-1V alloy compared to Ti-6Al-4V[J]. Material Design, 2011, 32(3):1692-1696.
    [7] Raja V S, Shoji T. Stress corrosion cracking[M]. Cambridge:Woodhead Publishing, 2011:381-408.
    [8] Wanhill R J H. Aqueous stress corrosion in titanium alloys[J]. British Corrosion Journal, 1975, 10:69-78.
    [9] 李晓延, 巩水利, 关 桥, 等. 大厚度钛合金结构电子束焊接制造基础研究[J]. 焊接学报, 2010, 31(2):107-112
    Li Xiaoyan, Gong Shuili, Guan Qiao, et al. Fundamental research on electron beam welding of heavy section titanium alloy structures[J]. Transactions of the China Welding Institution, 2010, 31(2):107-112
    [10] Weglowski M S, Blacha S, Phillips A. Electron beam welding-techniques and trends-review[J]. Vacuum, 2016, 130:72-92.
    [11] 石铭霄. 钛合金电子束深熔焊传热传质及质量控制研究[D]. 兰州:兰州理工大学, 2013.
    [12] 侯江涛. TC4 钛合金高能束流焊接焊缝组织研究[D]. 武汉:华中科技大学, 2009.
    [13] 吴会强, 冯吉才, 何景山, 等. 电子束焊接热输入对 Ti-6Al-4V 组织结构的影响[J]. 焊接学报, 2004, 25(5):41-44
    Wu Huiqiang, Feng Jicai, He Jingshan, et al. Effect of electron beam welding heat input on microstructure of Ti-6Al-4V[J]. Transactions of the China Welding Institution, 2004, 25(5):41-44
    [14] 龚玉兵, 王善林, 李 娟, 等. 厚板TC4钛合金电子束焊接头组织演变规律[J]. 焊接学报, 2017, 38(9):91-96
    Gong Yubing, Wang Shanlin, Li Juan, et al. Microstructure evolution of thick TC4 titanium alloy vacuum electron beam welded joint[J]. Transactions of the China Welding Institution, 2017, 38(9):91-96
    [15] 安飞鹏, 王其红, 李士凯, 等. 深潜器用Ti80电子束焊接接头精细组织结构特征[J]. 焊接学报, 2017, 38(5):96-99
    An Feipeng, Wang Qihong, Li Shikai, et al. Microstructure of electron beam welded thick-wall Ti80 joint[J]. Transactions of the China Welding Institution, 2017, 38(5):96-99
    [16] 旷小聪. 超大厚度TA15钛合金电子束焊接及热处理工艺研究[D]. 南昌:南昌航空大学, 2017.
    [17] 余 陈, 张宇鹏, 房卫萍, 等. 焊后热处理对100 mm TC4钛合金电子束焊接接头残余应力的影响[J]. 材料热处理学报, 2018, 39(7):151-155
    Yu Chen, Zhang Yupeng, Fang Weiping, et al. Effect of post welding heat treatment on residual stress of 100 mm TC4 Ti-alloy welded joint by electron beam welding[J]. Transactions of Materials and Heat Treatment, 2018, 39(7):151-155
    [18] 吴 冰, 张建勋, 巩水利, 等. 厚板钛合金电子束焊接残余应力分布特征[J]. 焊接学报, 2010, 31(2):10-12
    Wu Bing, Zhang Jianxun, Gong Shuili, et al. Residual stress distribution of large thickness titanium alloy joints by electron beam welding[J]. Transactions of the China Welding Institution, 2010, 31(2):10-12
    [19] Han W, Fu L, Chen H Y. Effect of welding speed on fatigue properties of TC18 thick plate by electron beam welding[J]. Rare Metal Materials and Engineering, 2018, 47(8):2335-2340.
    [20] 吴俊升, 林 超, 彭冬冬, 等. Q345D低合金钢在海洋潮差区的腐蚀规律及电化学行为研究[J]. 机械工程学报, 2016, 52(20):30-36
    Wu Junsheng, Lin Chao, Peng Dongdong, et al. Electrochemical investigation and corrosion behavior of low alloy steel Q345D in marine tidal zone[J]. Journal of Mechanical Engineering, 2016, 52(20):30-36
    [21] 马宏驰, 刘智勇, 杜翠薇, 等. SO2质量分数对污染海洋大气环境中高强钢E690腐蚀行为的影响[J]. 机械工程学报, 2016, 52(16):33-41
    Ma Hongchi, Liu Zhiyong, Du Cuiwei, et al. Effect of SO2 content on corrosion behavior of high-strength steel E690 in polluted marine atmosphere[J]. Journal of Mechanical Engineering, 2016, 52(16):33-41
    [22] 黄 涛, 陈小平, 王向东, 等. 高强耐候钢在NaCl溶液中的腐蚀锈层特征和耐腐蚀性研究[J]. 机械工程学报, 2017, 53(20):45-53
    Huang Tao, Chen Xiaoping, Wang Xiangdong, et al. A study on the rust characteristics and corrosion resistance of high strength weathering steels in NaCl solution[J]. Journal of Mechanical Engineering, 2017, 53(20):45-53
    [23] 刘 焱. 感应热处理TC4合金焊缝的应力腐蚀及慢拉伸时电化学行为[D]. 哈尔滨:哈尔滨工业大学, 2017.
    [24] Sheng C, Suming Z, Chao V, et al. The mechanism of aqueous stress-corrosion cracking of α + β titanium alloys[J]. Corrosion Science, 2017, 125:29-39.
    • 相关文章
    • 施引文献(12)

  • 期刊类型引用(5)

    1. 吴叶军，胥国祥，王加友，陈保国. 辅丝对摇动电弧窄间隙GMA焊接温度场的影响. 焊接. 2024(08): 1-9 . 百度学术
    2. 吴叶军，胥国祥，王加友，陈保国. 考虑侧壁热源的摇动电弧窄间隙GMA焊接温度场有限元模拟. 机械工程材料. 2024(11): 119-127 . 百度学术
    3. 冯睿，王磊，陆万全，王光宇，乔及森. 焊剂片约束电弧焊T形接头温度场有限元模拟. 兰州理工大学学报. 2022(05): 1-7 . 百度学术
    4. 徐刚，张天雷，何林基，沈艳涛，马春伟. 摆动电弧窄间隙厚板焊接工艺与熔池演变数值研究. 轻工机械. 2021(01): 40-46 . 百度学术
    5. 胥国祥，朱杰，王加友，李林，郑志强. 摇动电弧窄间隙FCAW立焊流体流动数值分析模型. 机械工程学报. 2019(18): 63-69 . 百度学术

    其他类型引用(7)

    • 资源附件(0)
计量
  • 文章访问数:  362
  • HTML全文浏览量:  9
  • PDF下载量:  46
  • 被引次数: 12
出版历程
  • 收稿日期:  2019-04-29

目录

摘要
HTML全文
    参考文献(24)
    相关文章
    施引文献(12)
    资源附件(0)

    /

    返回文章
    返回

    网站版权 © 焊接杂志社焊接学报编辑部电话：0451-86323218地址：哈尔滨市松北区创新路2077号

    本系统由 北京仁和汇智信息技术有限公司 开发  百度统计