WC和Al2O3对氩弧熔覆FeAlCoCrCuTi0.4高熵合金涂层组织和耐冲蚀性能影响
Effects of WC and Al2O3 on the microstructure and erosion wear resistance of FeAlCoCrCuTi0.4 high-entropy alloy coating by argon arc cladding
-
摘要: 利用氩弧熔覆技术制备了FeAlCoCrCuTi0.4,WC/Al2O3-FeAlCoCrCuTi0.4高熵合金涂层,并通过XRD,SEM,EDS,硬度测试和冲蚀磨损测试等方法,探究了WC和Al2O3的添加对FeAlCoCrCuTi0.4高熵合金涂层显微组织和性能的影响.结果表明,通过氩弧熔覆技术所制备的合金涂层表面成形性良好,无孔洞、裂纹等缺陷产生,与基体呈高强度冶金结合.WC和Al2O3的添加对涂层稀释率的降低有显著作用.三种涂层都是主要由Bcc相(Fe-Cr固溶体)构成,晶粒以胞状树枝晶形式存在.添加WC后,晶粒细化明显,在各种强化作用下涂层硬度为685.8 HV.且WC和Al2O3的添加显著提高了涂层耐冲蚀磨损性能,耐磨性几乎可以达到FeAlCoCrCuTi0.4高熵合金涂层的2倍.Abstract: FeAlCoCrCuTi0.4, WC/Al2O3-FeAlCoCrCuTi0.4 high-entropy alloy (HEA) coating had been cladded by means of argon arc cladding. The effects of WC and Al2O3 on microstructure and properties of FeAlCoCrCuTi0.4 high entropy alloy coatings were investigated by means of XRD, SEM, EDS, hardness testing and erosion wear testing. The results show that the alloy coating prepared by argon arc cladding has good formability, no holes, cracks and other defects, and high strength metallurgical bonding with the matrix. The addition of WC and Al2O3 has a significant effect on reducing the dilution rate of the coating. The three kinds of coatings are mainly composed of BCC phase (Fe-Cr solid solution), and the grains exist in the form of cellular dendrites. After adding WC, the grain size is obviously refined, and the hardness of the coating is 685.8 HV under various strengthening effects. The addition of WC and Al2O3 significantly improved the erosion wear resistance of the coating, and the wear resistance could almost reach 2 times of that of FeAlCoCrCuTi0.4 high entropy alloy coating.
-
Keywords:
- high entropy alloy /
- composite coating /
- hardness /
- erosion wear resistance
-
-
[1] 魏国庆.金属材料磨损失效及改善措施[J].科技经济导刊, 2017(14):113-114 Wei Guoqing. Wear failure and improvement measures of metal materials[J]. Technology and Economic Guide, 2017(14):113-114 [2] Yang K, Rong J, Feng J, et al. Excellent wear resistance of plasma-sprayed amorphous Al2O3-Y3Al5O12 ceramic coating[J]. Surface and Coatings Technology, 2017, 326:96-102. [3] 韩婷婷,龙威,周小平. Mg3Sb2含量对Al-Mg3Sb2复相涂层耐磨性的影响[J].表面技术, 2018, 47(2):83-88 Han Tingting, Long Wei, Zhou Xiaoping. Effect of Mg3Sb2 content on wear resistance of Al-Mg3Sb2 composite coatings[J]. Surface Technology, 2018, 47(2):83-88 [4] 蔡玮玮,邵帅,吴来军.低合金钢表面Fe基B4C耐磨涂层组织与性能[J].表面技术, 2018, 47(2):130-135 Cai Weiwei, Shao Shuai, Wu Laijun. Microstructure and properties of Fe-based B4C wear-resistant coating on 16Mn steel[J]. Surface Technology, 2018, 47(2):130-135 [5] Yeh J W, Chen S K, Lin S J, et al. Nanostructured high-entropy alloys with multiple principal elements:novel alloy design concepts and outcomes[J]. Advanced Engineering Materials, 2004, 6(5):299-303. [6] Qiu X. Microstructure, hardness and corrosion resistance of Al2CoCrCuFeNiTix high-entropy alloy coatings prepared by rapid solidification[J]. Journal of Alloys and Compounds, 2018, 735:359-364. [7] Shu F Y, Liu S, Zhao H Y, et al. Structure and high-temperature property of amorphous composite coating synthesized by laser cladding FeCrCoNiSiB high-entropy alloy powder[J]. Journal of Alloys and Compounds, 2018, 731:662-666. [8] 王小荣,王朝琴,何鹏,等. 45钢表面高能微弧火花数控化沉积AlCoCrFeNi高熵合金[J].焊接学报, 2016, 37(10):73-76 Wang Xiaorong, Wang Zhaoqin, He Peng, et al. Numerical control deposition of AlCoCrFeNi high-entropy alloy on 45 steel by high energy micro arc spark[J]. Transactions of the China Welding Institution, 2016, 37(10):73-76 [9] 王振廷,陈丽丽,张显友.钛合金表面氩弧熔覆TiC增强复合涂层组织与性能分析[J].焊接学报, 2008, 29(9):43-45 Wang Zhenting, Chen Lili, Zhang Xianyou. Microstructure and properties of TiC reinforced composite coating fabricated on Ti alloy by GTAW[J]. Transactions of the China Welding Institution, 2008, 29(9):43-45 [10] 王振廷,朱士奎,冯帆.石墨电极表面氩弧熔覆原位合成ZrB2-SiC/Si抗氧化涂层[J].焊接学报, 2015, 36(8):55-58 Wang Zhenting, Zhu Shikui, Feng Fan. Research of in-suit synthesis of ZrB2-SiC/Si high temperature oxidation resistant coating on graphite by argon arc cladding[J]. Transactions of the China Welding Institution,, 2015, 36(8):55-58 [11] Zhang Y, Zhou Y J, Lin J P, et al. Solid-solution phase formation rules for multi-component alloys[J]. Advanced Engineering Materials, 2008, 10(6):534-538. [12] Takeuchi A, Inoue A. Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element[J]. Materials Transactions, 2005, 46(12):2817-2829. -
期刊类型引用(12)
1. 靖微,王小伟,刘书明,邹文凤,张旗,杨岩. 侧板用HJ58和WL510钢自动焊工艺及焊缝组织与性能研究. 兵器材料科学与工程. 2025(02): 133-138 . 百度学术
2. 刘文吉,肖宇,杨嘉昇,朱鹏飞. 窄间隙P-GMAW仰焊位置熔滴过渡影响因素及控制方法. 焊接学报. 2024(01): 58-63+132-133 . 本站查看
3. 马汉勇,张旗,靖微,何龙,许经伟,李新兴. 小底架焊接变形控制工艺. 焊接技术. 2023(07): 121-125 . 百度学术
4. 罗雨,吉天亮,高萌萌,王东尧. X65管线钢窄坡口旋转电弧焊焊接工艺与性能. 焊接. 2023(07): 26-33 . 百度学术
5. 孙连北,魏坤霞,孟涛,张尧成,魏伟. 等离子弧焊Q345B和430不锈钢异种接头的微观组织与性能. 焊接. 2022(05): 19-23 . 百度学术
6. 杨泽坤,杨战利,赵宝,肖秀程,赵德民,李洪涛. 异种钢焊接接头失效机制的研究进展. 焊接. 2022(08): 17-24+32 . 百度学术
7. 郑韶先,徐龙强,赵锡龙,史伟. 预置镍基合金片对异种钢UNGW接头组织及性能的影响. 焊接. 2021(01): 1-7+61 . 百度学术
8. 孙捷夫,孔繁霁,杨巍,单英吉. 基于响应面法的1Cr18Ni9Ti不锈钢车削参数优化. 机床与液压. 2021(13): 65-69 . 百度学术
9. 张敏,杜明科,张云龙,王刚,朱子越. Q345B低碳钢/20Mn23Al无磁钢异种钢焊接接头的组织及性能. 机械工程材料. 2021(08): 66-71 . 百度学术
10. 任玲,范玉婷. 42CrMo/Q345异种钢焊接接头疲劳性能试验研究. 热处理技术与装备. 2021(05): 29-34 . 百度学术
11. 王招阳,李金全,肖长源,袁立铭,林健,雷永平,李康立. 321不锈钢激光增材制造工艺及变形研究. 航天制造技术. 2020(06): 40-44+52 . 百度学术
12. 张建晓,刘光银,刘世恩,黄健康,樊丁. 12Cr2Mo1R耐热钢/304不锈钢异种钢焊接. 焊接. 2020(10): 7-13+61-62 . 百度学术
其他类型引用(7)
计量
- 文章访问数: 487
- HTML全文浏览量: 10
- PDF下载量: 97
- 被引次数: 19