铝合金T形接头静止轴肩搅拌摩擦焊接及组织性能分析
Analysis of microstructure and mechanical properties of the aluminum alloy T-joint welded by stationary shoulder friction stir welding
-
摘要: 成功实现了2219C10S铝合金T形接头的静止轴肩搅拌摩擦焊接，焊缝表面光滑平整，无明显减薄.从基板背部进行的超声相控阵检测结果表明，基板与肋板对合面全部焊透，接头内部无超标缺陷.接头横截面宏观金相可以观察到2个以肋板中心线对称分布的焊缝轮廓，单侧焊缝轮廓均超过了肋板中心线.接头横截面显微硬度分布趋势呈独特的“U”形，焊核区显微硬度最低.T形接头两个方向的拉伸试样起裂点位于“拉伸方向板材与接头R1圆角的相切处”，但拉断试样断裂面的横穿区域存在较大差异，这也是沿肋板方向的抗拉强度比沿基板方向低20 MPa的主要原因.
-
关键词:
- T形接头 /
- 静止轴肩搅拌摩擦焊接 /
- 显微硬度 /
- 拉伸性能 /
- 断裂位置
Abstract: 2219C10S aluminum alloy T-joint was successfully performed by stationary shoulder friction stir welding. The weld surface is smooth and has no obvious thickness-reduction. The PAUT testing on the back of the substrate plate shows that all the surfaces between the substrate and rib plates were welded thoroughly. The macro-structure revealed two weld contours symmetrically distributed in the center of the rib plate. The unilateral weld contours also exceeded the center line of the rib plate. The microhardness distribution of the joints shows a unique U-shaped distribution, and the microhardness of the weld nugget zone was the lowest. The crack of tensile specimens with the two directions of T-joint initiated at the tangent of the tension plate and the corner of the joint R1. However, the transverse areas of the fracture surface for the two types of tensile specimens are quite different. This is the main reason why the tensile strength along the direction of rib plate was 20 MPa lower than that along the direction of the substrate plate. -
-
[1] Wang Guoqing, Zhao Yanhua, Hao Yunfei. Friction stir welding of high-strength aerospace aluminum alloy and application in rocket tank manufacturing[J]. Journal of Materials Science&Technology, 2018, 34(1):73-91. [2] 郝云飞,王国庆,周庆,等.运载火箭铝合金贮箱全搅拌摩擦焊接工艺及应用[J].宇航材料工艺, 2016, 46(6):11-20 Hao Yunfei, Wang Guoqing, Zhou Qing, et al. Application of all friction stir welding technology on the launch vehicle tank[J]. Aerospace Materials&Technology, 2016, 46(6):11-20 [3] 刘会杰,李金全,段卫军,等.静止轴肩搅拌摩擦焊的研究进展[J].焊接学报, 2012, 33(5):108-111 Liu Huijie, Li Jinquan, Duan Weijun, et al. Progress in the stationary shoulder friction stir welding[J]. Transactions of the China Welding Institution, 2012, 33(5):108-111 [4] Widener C A, Talia J E, Tweedy B M, et al. High-rotational speed friction stir welding with a fixed shoulder[C]//6th International Symposium on Friction Stir Welding, Montreal, Canada, 2006:10− 13. [5] Crawford R, Bloodworth T, Cook G E, et al. High speed friction stir welding process modeling[C]//6th International Symposium on Friction Stir Welding, Montreal, Canada, 2006:20− 25. [6] Wynne B P, Threadgill P L, Davies P S, et al. Microstructure and texture in static shoulder friction stir welds of Ti-6Al-4V[C]//7th International Friction Stir Welding Symposium, Awaji Island, Japan, 2008:20− 22. [7] Jiang Xiaoqing, Bradley P Wynne, Jonathan Martin. Variant selection in stationary shoulder friction stir welded Ti-6Al-4V alloy[J]. Journal of Materials Science&Technology, 2018, 34(1):198-208. [8] 吉华,徐萌,封小松,等.静止轴肩搅拌摩擦焊T型接头组织及力学行为[J].电焊机, 2013, 43(9):37-40 Ji Hua, Xu Meng, Feng Xiaosong, et al. Research on microstructure and mechanical behavior of T-joint welded by stationary shoulder friction stir welding[J]. Electric Welding Machine, 2013, 43(9):37-40 [9] Sun Zhuanping, Yang Xinqi, Li Dongxiao, et al. The local strength and toughness for stationary shoulder friction stir weld on AA6061-T6 alloy[J]. Materials Characterization, 2016, 111:114-121. [10] 武颖,李迎,张玉芝. 2219铝合金静止轴肩搅拌摩擦焊接头组织及性能[J].宇航材料工艺, 2018, 48(3):56-60 Wu Ying, Li Ying, Zhang Yuzhi. Microstructure and properties of 2219 aluminum alloy joint obtained by stationary shoulder friction stir welding[J]. Aerospace Materials&Technology, 2018, 48(3):56-60 [11] 何方舟,杨新岐,李冬晓,等.铝合金静止轴肩搅拌摩擦焊组织非均质性对接头力学性能的影响[J].焊接学报, 2017, 38(8):115-118 He Fangzhou, Yang Xinqi, Li Dongxiao, et al. Effect of microstructural inhomogeneity on mechanical properties of stationary shoulder friction stir welded joints for 6061-T6 aluminum alloy[J]. Transactions of the China Welding Institution, 2017, 38(8):115-118 [12] 张坤,方远方,栾国红,等.静止轴肩搅拌摩擦焊接6005铝合金的力学和疲劳性能[J].焊接学报, 2017, 38(10):25-28 Zhang Kun, Fang Yuanfang, Luan Guohong, et al. Mechanical and fatigue property of stationary shoulder friction stir welding AA6005[J]. Transactions of the China Welding Institution, 2017, 38(10):25-28 [13] 申浩,杨新岐,李冬晓,等. 6061-T6铝合金的静止轴肩搅拌摩擦焊工艺及组织性能[J].焊接学报, 2016, 37(5):119-122 Shen Hao, Yang Xinqi, Li Dongxiao, et al. Microstructures and mechanical properties of 6061-T6 aluminum alloy welded by stationary shoulder friction stir welding process[J]. Transactions of the China Welding Institution, 2016, 37(5):119-122 -
期刊类型引用(13)
1. 赵衍华，张粟泓，王非凡，郝云飞，宋建岭，孙世烜，王国庆. 搅拌摩擦焊接与加工技术进展. 航天制造技术. 2025(01): 1-25 . 
百度学术
2. 张亚，赵云峰，戴忠晨，孙博，胡霞，施海霞. 6061-T6铝合金静止轴肩搅拌摩擦焊角接接头焊接工艺研究. 电焊机. 2025(04): 64-72 . 百度学术
3. 邹阳，魏巍，范悦，王泽震，王强，赵亮. 铝合金搅拌摩擦焊工艺研究进展. 热加工工艺. 2024(03): 7-13 . 百度学术
4. 强伟，王克鸿，彭勇，袁银辉，路永新，董会. V形耦合双热源自熔焊接热-力分布特征. 稀有金属. 2024(04): 529-538 . 百度学术
5. 秦丰，张春波，周军，乌彦全，梁武，巫瑞智. 5A06铝合金静止轴肩搅拌摩擦焊T形接头组织与性能. 焊接学报. 2022(06): 56-60+95+116 . 本站查看
6. 温泉，李文亚，吴雪猛，任寿伟，赵静. 单静止上轴肩BT-FSW工艺过程及成形机理. 焊接学报. 2022(07): 88-96+118-119 . 本站查看
7. 李冬晓，张斌，张俊林，刘淑芬，姜坤，杨新岐. AA6061填丝FSW T形接头特征及动静载特性分析. 焊接学报. 2021(04): 62-68+91+100 . 本站查看
8. 夏佩云，尹玉环，董吉义，吕红亚，王春明，赵慧慧，封小松. 轴肩型面对角接接头静轴肩搅拌摩擦焊缝成形的影响. 航空制造技术. 2021(13): 96-101 . 百度学术
9. 强伟，路永新，袁银辉，孙粲. T形接头冷丝填充双热源协同焊接数值模拟. 材料科学与工艺. 2021(05): 57-62 . 百度学术
10. 杨海峰，赵洪运，许欣欣，孙广达，周利，赵慧慧，刘会杰. 静轴肩搅拌摩擦焊2A14-T4铝合金T形接头的组织和性能. 材料导报. 2021(20): 20045-20051 . 百度学术
11. 李冬晓，杨纯，黄鑫，邢广强，杨新岐. 静轴肩FSW铝合金6061-T4板的T形接头组织特征及动静载特性研究. 机械工程学报. 2021(20): 108-116 . 百度学术
12. 丁晓静. 高层建筑用AA3004铝合金板材屈曲特性分析. 兵器材料科学与工程. 2020(04): 46-50 . 百度学术
13. 吴进军，吕晋，杜兵，朱宇宏，张林. 基于专利大数据的焊接前沿热点技术挖掘. 焊接. 2019(12): 1-6+65 . 百度学术
其他类型引用(2)
计量
- 文章访问数: 401
- HTML全文浏览量: 5
- PDF下载量: 143
- 被引次数: 15
下载:
