高级检索

焊接速度对6005A-T6铝合金双轴肩搅拌摩擦焊接头力学性能的影响

吉华, 邓运来, 邓建峰, 徐红勇, 林森

吉华, 邓运来, 邓建峰, 徐红勇, 林森. 焊接速度对6005A-T6铝合金双轴肩搅拌摩擦焊接头力学性能的影响[J]. 焊接学报, 2019, 40(5): 24-29. DOI: 10.12073/j.hjxb.2019400122
引用本文: 吉华, 邓运来, 邓建峰, 徐红勇, 林森. 焊接速度对6005A-T6铝合金双轴肩搅拌摩擦焊接头力学性能的影响[J]. 焊接学报, 2019, 40(5): 24-29. DOI: 10.12073/j.hjxb.2019400122
JI Hua, DENG Yunlai, DENG Jianfeng, XU Hongyong, LIN Sen. Effect of welding speed on mechanical properties of bobbin tool friction stir welded 6005A-T6 aluminum alloy joints[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(5): 24-29. DOI: 10.12073/j.hjxb.2019400122
Citation: JI Hua, DENG Yunlai, DENG Jianfeng, XU Hongyong, LIN Sen. Effect of welding speed on mechanical properties of bobbin tool friction stir welded 6005A-T6 aluminum alloy joints[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2019, 40(5): 24-29. DOI: 10.12073/j.hjxb.2019400122

焊接速度对6005A-T6铝合金双轴肩搅拌摩擦焊接头力学性能的影响

基金项目: 国家重点研发计划资助项目(2016YFB0300901)

Effect of welding speed on mechanical properties of bobbin tool friction stir welded 6005A-T6 aluminum alloy joints

  • 摘要: 文中研究了转速和热输入特征值WP一定两种条件下焊接速度对6005A-T6铝合金双轴肩搅拌摩擦焊接头力学性能的影响. 结果表明,转速一定时,接头抗拉强度随焊接速度的增加呈先增大后减小的趋势;热输入特征值WP一定时,随着焊接速度的增加,接头的抗拉强度持续减小;接头呈现出三种断裂方式,分别为发生于热影响区的Ⅰ型断裂、发生于焊核区的Ⅱ型断裂和发生于热力影响区的Ⅲ型断裂;Ⅰ型断裂和Ⅱ型断裂为韧性断裂;Ⅲ型断裂为包含韧性断裂和脆性断裂的混合型断裂;接头拉伸断裂位置并非总出现在硬度最低处;焊接速度小于1 000 mm/min时,WP ≤ 1有利于提高接头力学性能,而焊接速度大于1 000 mm/min时,WP > 1更有利于提高接头力学性能.
    Abstract: Effect of welding speed on mechanical properties of 6005A-T6 aluminum alloy joints welded by bobbin tool friction stir welding method was investigated under a constant rotation speed and heat input factor (Ratio of welding speed and rotation speed, WP). The results show that under a certain rotation speed, the tensile stress increased and then decreased with the increasing of welding speed. While under a certain WP, the tensile stress decreased continuously with the increasing of welding speed. Three typical fracture morphology were found in bobbin tool friction stir welded joints, namely, I type fracture at the heat affected zone (HAZ), Ⅱ type fracture at the weld nugget zone (WNZ) and Ⅲ type fracture at the thermal-mechanical affected zone (TMAZ). The macro morphology of I and Ⅱ type fracture were cup and cone morphology, serrated morphology, respectively. However, the microstructure indicated that both of them featured with toughness failure. Ⅲ type fracture was identified to be mixed fracture which consists of toughness failure and brittle failure. The tensile fracture position is not always occurred at the position with minimum microhardness. When the welding speed was lower than 1 000 mm/min, WP less than 1 is benefit to obtain joints with higher tensile strength and I type fracture. On the contrary, when welding speed was higher than 1 000 mm/min, WP more than 1 is benefit to obtain joints with higher tensile strength and I type fracture.
  • [1] Wang Guoqing, Zhao Yanhua, Zhang Lina, et al. A new weld repair technique for friction stir welded aluminium structure:inertia friction pull plug welding[J]. China Welding, 2017, 26(4):56-64.
    [2] 侍光磊,张璟瑜,胡丰,等. 6005A-T6铝合金型材双轴肩搅拌摩擦焊接头组织及力学性能[J].焊接, 2017(8):21-25 Shi Guanglei, Zhang Jingyu, Hu feng, et al. Microstructure and mechanical properties of bobbin tool frication stir welded joint of 6005A-T6 aluminum alloy profiles[J]. Welding&Joining, 2017(8):21-25
    [3] 戴忠晨,云中煌,付宁宁,等. 5 mm厚6005A-T6铝合金双轴肩搅拌摩擦焊接头的组织及性能[J].机械工程材料, 2018, 42(2):69-73 Dai Zhongchen, Yun Zhonghuang, Fu Ningning, et al. Microstructure and properties of bobbin tool friction stir welded joint of 5 mm thick 6005A-T6 aluminum alloy[J]. Materials for Mechanical Engineering, 2018, 42(2):69-73
    [4] 潘锐,王善林,李健萍,等.工艺参数对搅拌摩擦焊变形铝合金接头性能的影响[J].焊接学报, 2016, 37(11):89-92 Pan Rui, Wang Shanlin, Li Jianping, et al. Effect of processing parameters on mechanical properties of aluminum alloy joints welded by friction stir welding[J]. Transactions of China Welding Institutions, 2016, 37(11):89-92
    [5] 郝云飞,魏瑞刚,周庆,等.焊接热输入对铝合金双轴肩搅拌摩擦焊缝形貌与接头性能的影响[J].焊接学报, 2018, 39(2):84-88 Hao Yunfei, Wei Ruigang, Zhou Qing, et al. Effect of heat input on weld morphology and tensile properties of bobbin friction stir welded joints[J]. Transactions of China Welding Institutions, 2018, 39(2):84-88
    [6] Liu H J, Hou J C, Guo H. Effect of welding speed on microstructure and mechanical properties of self-reacting friction stir welded 6061-T6 aluminum alloy[J]. Materials and Design, 2013, 50:872-878.
    [7] Zhou L, Li G H, Liu C L, et al. Effect of rotation speed on microstructure and mechanical properties of self-reacting friction stir welded Al-Mg-Si alloy[J]. The International Journal of Advanced Manufacturing Technology, 2017, 89(9-12):3509-3516.
    [8] Dong Jihong, Gao Chong, Lu Yao, et al. Microstructural characteristics and mechanical properties of bobbin-tool friction stir welded 2024-T3 aluminum alloy[J]. International Journal of Minerals Metallurgy and Materials, 2017, 24(2):171-178.
    [9] Esmaily M, Mortazavi N, Osikowicz W, et al. Bobbin and conventional friction stir welding of thick extruded AA6005-T6 profiles[J]. Materials and Design, 2016, 108:114-125.
    [10] 李红英.金属拉伸试样的断口分析[J].山西大同大学学报, 2011, 27(1):76-79 Li Hongying. Fracture analysis of metal tensile specimen[J]. Journal of Shanxi Datong University, 2011, 27(1):76-79
    [11] 乔岩欣,周洋,陈书锦,等.双轴肩搅拌摩擦焊对6061-T6铝合金表面组织及其在3.5% NaCl中腐蚀行为的影响[J].金属学报, 2017, 52(11):1395-1402 Qiao Yanxin, Zhou Yang, Chen Shujin, et al. Effect of bobbin tool friction stir welding on microstructure and corrosion behavior of 6061-T6 aluminum alloy joint in 3.5% NaCl solution[J]. Acta Metallurgica Sinica, 2017, 52(11):1395-1402
  • 期刊类型引用(20)

    1. 马霄锋,杨冠华,高超,钮旭晶,王玮彤. 6005A-T6铝合金对搭接FSW接头微观组织与力学性能. 焊接技术. 2025(03): 8-13+145 . 百度学术
    2. 邹阳,魏巍,范悦,王泽震,王强,赵亮. 铝合金搅拌摩擦焊工艺研究进展. 热加工工艺. 2024(03): 7-13 . 百度学术
    3. 蹇文轩,丛孟启,雷卫宁. 基于搅拌摩擦加工技术的镁基复合材料研究进展. 机械工程学报. 2024(08): 48-64 . 百度学术
    4. 冯家铖,宫文彪,鞠川,李于朋,孙雨萌,朱芮. 2024铝合金双轴肩搅拌摩擦焊接头热循环及组织特征. 吉林大学学报(工学版). 2024(11): 3184-3191 . 百度学术
    5. 邓建峰,郭伟强,徐晓霞,王博,灰辉,窦思忠,黄望业. Comprehensive study of microstructure and mechanical properties of friction stir welded 5182-O/HC260YD + Z lap joint. China Welding. 2023(01): 46-52 . 百度学术
    6. 谢宇,李兴帅,付炳欣. 轨道交通铝合金车体双轴肩搅拌摩擦焊研究现状与展望. 机车车辆工艺. 2023(03): 18-20+28 . 百度学术
    7. 尹德猛,李充,姚肖洁,郝文波,王崴,杨彦龙. 6082-T6铝合金双轴肩搅拌摩擦焊接头成形及力学性能. 焊接. 2023(06): 38-43 . 百度学术
    8. 鲁克锋,殷凤仕,王文宇,滕涛,樊世冲,刘亚凡,王鸿琪,朱建,任智强. 铝合金搅拌摩擦焊接头缺陷及焊件结构问题控制策略的研究进展. 表面技术. 2023(07): 55-79 . 百度学术
    9. 温泉,李文亚,吴雪猛,任寿伟,赵静. AA6056双轴肩搅拌摩擦焊接头非均匀性分析. 焊接学报. 2023(09): 88-94+134 . 本站查看
    10. 马佳良,曾泽群,孙屹博,杨鑫华. 工艺参数对铝合金搅拌摩擦焊变形和残余应力的影响及优化. 焊接技术. 2022(01): 46-52+114 . 百度学术
    11. 张颖川,马国栋,代鹏,王敬水,金炜. 6061-T6铝合金中空薄壁型材双轴肩搅拌摩擦焊工具设计与工艺分析. 焊接学报. 2022(06): 88-95+118 . 本站查看
    12. 林森,韩晓辉,李刚卿,王鹏,赵存金,杨志斌. 高速列车铝合金MIG接头应力腐蚀失效研究. 中国安全科学学报. 2022(06): 115-122 . 百度学术
    13. 李帅贞,韩晓辉,吴来军,刘裕航,王鹏,宋晓国,檀财旺. 层道排布对6005A铝合金MIG焊接头微观组织及力学性能的影响. 材料导报. 2022(17): 157-161 . 百度学术
    14. 赵刚,颜旭,王立梅,柴煜,郝云飞. 焊接工艺参数对10mm厚2219铝合金双轴肩搅拌摩擦焊焊缝质量和性能的影响. 焊接. 2022(12): 13-19 . 百度学术
    15. 李小欣,郑延召,徐仲勋,王晓贞. 焊接参数对5A06铝合金搅拌摩擦焊接头性能的影响. 上海金属. 2021(03): 19-25 . 百度学术
    16. 李充,李朔晗,齐振国,孟祥晨,黄永宪. 对接间隙对双轴肩搅拌摩擦焊接头成形与性能的影响. 焊接. 2021(09): 5-9+27+61 . 百度学术
    17. 李志强,陈辰. 铝合金材料搅拌摩擦焊焊接参数概述. 焊接技术. 2021(11): 1-5 . 百度学术
    18. 方远方,张华,窦程亮. 2A12-T4/7A09-T6铝合金搅拌摩擦焊搭接接头性能分析. 焊接学报. 2020(01): 86-90+101-102 . 本站查看
    19. 李少峰,马成勇,宋志刚,安同邦. 800 MPa级高强钢焊接接头组织及力学性能. 焊接学报. 2020(05): 91-96+102 . 本站查看
    20. 吴进军,吕晋,杜兵,朱宇宏,张林. 基于专利大数据的焊接前沿热点技术挖掘. 焊接. 2019(12): 1-6+65 . 百度学术

    其他类型引用(7)

计量
  • 文章访问数:  424
  • HTML全文浏览量:  4
  • PDF下载量:  71
  • 被引次数: 27
出版历程
  • 收稿日期:  2017-12-26

目录

    /

    返回文章
    返回