高级检索

采用镍基和奥氏体焊材焊接Cr13钢焊接接头性能

张雅芝1,张国栋2,杨辉2,王麒瑜2

张雅芝1,张国栋2,杨辉2,王麒瑜2. 采用镍基和奥氏体焊材焊接Cr13钢焊接接头性能[J]. 焊接学报, 2018, 39(8): 102-107. DOI: 10.12073/j.hjxb.2018390210
引用本文: 张雅芝1,张国栋2,杨辉2,王麒瑜2. 采用镍基和奥氏体焊材焊接Cr13钢焊接接头性能[J]. 焊接学报, 2018, 39(8): 102-107. DOI: 10.12073/j.hjxb.2018390210
shu
ZHANG Yazhi1, ZHANG Guodong2, YANG Hui2, WANG Qiyu2. Properties of Cr13 steel joints welded by nickel-based and austenite welding materials[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2018, 39(8): 102-107. DOI: 10.12073/j.hjxb.2018390210
Citation: ZHANG Yazhi1, ZHANG Guodong2, YANG Hui2, WANG Qiyu2. Properties of Cr13 steel joints welded by nickel-based and austenite welding materials[J]. TRANSACTIONS OF THE CHINA WELDING INSTITUTION, 2018, 39(8): 102-107. DOI: 10.12073/j.hjxb.2018390210
shu

采用镍基和奥氏体焊材焊接Cr13钢焊接接头性能

  • 1. 中车株洲电机有限公司, 株洲 412000;
    2. 武汉大学 动力与机械学院, 武汉 430072

基金项目: 国家自然科学基金（51374151）；湖北省自然科学基金资助项目（2014CFB707）

Properties of Cr13 steel joints welded by nickel-based and austenite welding materials

  • 1. CRRC Zhuzhou Electric Co., Ltd, Zhuzhou 412000, China;
    2. School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072, China

摘要

    摘要
  • 摘要: 采用ER309L氩弧焊丝的奥氏体焊材和ERNiCrFe-3镍基焊丝的镍基焊材对Cr13钢母材进行TIG焊接，通过无损检测、显微组织、力学性能和耐腐蚀性能试验，对两种焊材的焊接接头性能进行研究.结果表明，两种焊接接头均未发现焊接缺陷，焊接接头属于高强匹配，弯曲性能合格.与奥氏体焊材焊缝相比，镍基焊材的焊缝冲击韧性低，硬度高，耐电化学腐蚀性能高.
    Abstract: ER309L Austenitic welding materials and ERNiCrFe-3flux-cored wire nickel-based are adopted to weld Cr13 steel by TIG welding method. The performance of the two weld joints are studied by non-destructive detection, micro-hardness tests, mechanical properties and corrosion resistance tests. The experiment results show that no welding defects exist in either welding joints, both welding joints are high strength matched with qualified bending performance. Compared with Austenitic weld metal, nickel-based weld metal has lower impact toughness, higher hardness and resistance to electrochemical corrosion.
    • HTML全文
    • 参考文献(10)
  • [1] 张勇, 覃作祥, 许鸿吉, 等. 经济型铁素体不锈钢焊接接头组织与耐蚀性能[J]. 焊接学报, 2012, 33(12):18-22 Zhang Yong, Qin Zuoxiang, Xu Hongji, et al. Microstructure and corrosion resistance of welding joints of economic ferritic stainless steel[J]. Transactions of the China Welding Institution, 2012, 33(12):18-22
    [2] 郑淮北, 叶晓宁, 张雪峰, 等. 12%Cr铁素体不锈钢粗晶区组织转变和晶粒长大及析出相分析[J]. 焊接学报, 2011, 32(6):37-40 Zheng Huaibei, Ye Xiaoning, Zhang Xuefeng, et al. Microstructure transformation, grain growth and precipitated phase of 12%Cr ferritic stainless steel in coarse grain zone[J]. Transactions of the China Welding Institution, 2011, 32(6):37-40
    [3] Hu Jincheng, Song Hongmei, Yu Ming, et al. Thermo-calc calculations and experimental study of microstructure of SUS 410s and SUS 430 ferrite stainless steels at high temperature[A]. Proceedings of Sino-Swedish Structural Materials Symposium, 2007:183-188.
    [4] 许泽建, 李玉龙, 李朋洲. 0Cr18Ni10Ti不锈钢焊接接头的显微硬度研究[J]. 金属学报, 2008, 44(5):636-640 Xu Zejian, Li Yulong, Li Pengzhou. Microhardness investigation of 0Cr18Ni10Ti stainless steel welded joint[J]. Acta Metallurgica Sinica, 2008, 44(5):636-640
    [5] 王宝森, 马朝晖, 朱双春, 等. 铁路货车用TCS345不锈钢焊接热影响区韧性分析[J]. 焊接学报, 2009, 30(12):97-100 Wang Baosen, Ma Zhaohui, Zhu Shuangchun, et al. Analysis on heat-affected zone toughness of railroad freight TCS345 stainless steel weld joints[J]. Transactions of the China Welding Institution, 2009, 30(12):97-100
    [6] 朱亮, 张永强, 辛宝. 410S钢板焊剂带约束电弧对接焊工艺试验[J]. 焊接技术, 2015, 44(2):40-42 Zhu Liang, Zhang Yongqiang, Xin Bao. Constricting arc butt welding process test of 410S steel plate with flux strips[J]. Welding Technology, 2015, 44(2):40-42
    [7] 陈庆雷. SUS301L奥氏体不锈钢激光焊接头组织与力学性能的研究[D]. 长春:吉林大学, 2012.
    [8] Keskitalo M, Sundqvist J, Mäntyjärvi K, et al. The influence of shielding gas and heat input on the mechanical properties of laser welds in ferritic stainless steel[J]. Physics Procedia, 2015, 78:222-229.
    [9] Taban E, Kaluc E, Dhooge A. Hybrid (plasma + gas tungsten arc) weld ability of modified 12% Cr ferritic stainless steel[J]. Materials and Design, 2009, 30:4236-4242.
    [10] Tuthill A H, Avery R E. Corrosion behavior of stainless steel and high-alloy weldments in aggressive oxidizing environments[J]. Welding Journal, 1993, 72(2):41-49.
    • 相关文章
    • 施引文献(5)

  • 期刊类型引用(2)

    1. 高成龙，李宪爽，龚巍，史然峰，徐祥久. TA2板材焊接接头组织及性能研究. 焊管. 2024(09): 40-43+56 . 百度学术
    2. 陈波，徐亦楠，方乃文，马一鸣，李丹晖. 不锈钢焊接接头点蚀机理研究现状. 金属加工(热加工). 2020(11): 75-82 . 百度学术

    其他类型引用(3)

    • 资源附件(0)
计量
  • 文章访问数:  719
  • HTML全文浏览量:  30
  • PDF下载量:  80
  • 被引次数: 5
出版历程
  • 收稿日期:  2017-04-07

目录

摘要
HTML全文
    参考文献(10)
    相关文章
    施引文献(5)
    资源附件(0)

    /

    返回文章
    返回

    网站版权 © 焊接杂志社焊接学报编辑部电话：0451-86323218地址：哈尔滨市松北区创新路2077号

    本系统由 北京仁和汇智信息技术有限公司 开发  百度统计